구차니의 잡동사니 모음

void

UARTDisable(uint32_t ui32Base)

{

    //

    // Check the arguments.

    //

    ASSERT(_UARTBaseValid(ui32Base));

    //

    // Wait for end of TX.

    //

    while(HWREG(ui32Base + UART_O_FR) & UART_FR_BUSY)

    {

    }

    //

    // Disable the FIFO.

    //

    HWREG(ui32Base + UART_O_LCRH) &= ~(UART_LCRH_FEN);

    //

    // Disable the UART.

    //

    HWREG(ui32Base + UART_O_CTL) &= ~(UART_CTL_UARTEN | UART_CTL_TXE |

                                      UART_CTL_RXE);

} 

9.2.2.27 GPIOPinTypeUART

Configures pin(s) for use by the UART peripheral.

Prototype:

void

GPIOPinTypeUART(unsigned long ulPort,

unsigned char ucPins)

Parameters:

ulPort is the base address of the GPIO port.

ucPins is the bit-packed representation of the pin(s).

Description:

The UART pins must be properly configured for the UART peripheral to function correctly. This

function provides a typical configuration for those pin(s); other configurations may work as well

depending upon the board setup (for example, using the on-chip pull-ups).

The pin(s) are specified using a bit-packed byte, where each bit that is set identifies the pin to

be accessed, and where bit 0 of the byte represents GPIO port pin 0, bit 1 represents GPIO

port pin 1, and so on.

Note:

This cannot be used to turn any pin into a UART pin; it only configures a UART pin for proper

operation. 

void

UARTConfigSetExpClk(uint32_t ui32Base, uint32_t ui32UARTClk,

                    uint32_t ui32Baud, uint32_t ui32Config)

{

    // Stop the UART.

    UARTDisable(ui32Base);

    // Set the baud rate.

    HWREG(ui32Base + UART_O_IBRD) = ui32Div / 64;

    HWREG(ui32Base + UART_O_FBRD) = ui32Div % 64;

    // Set parity, data length, and number of stop bits.

    HWREG(ui32Base + UART_O_LCRH) = ui32Config;

    // Clear the flags register.

    HWREG(ui32Base + UART_O_FR) = 0;

    // Start the UART.

    UARTEnable(ui32Base);

} 

void

UARTEnable(uint32_t ui32Base)

{

    //

    // Check the arguments.

    //

    ASSERT(_UARTBaseValid(ui32Base));

    //

    // Enable the FIFO.

    //

    HWREG(ui32Base + UART_O_LCRH) |= UART_LCRH_FEN;

    //

    // Enable RX, TX, and the UART.

    //

    HWREG(ui32Base + UART_O_CTL) |= (UART_CTL_UARTEN | UART_CTL_TXE |

                                     UART_CTL_RXE);

}

 45 # HistoryName allows you to specify the name of the history file produced

 46 # by the Webalizer.  The history file keeps the data for previous months,

 47 # and is used for generating the main HTML page (index.html). The default

 48 # is a file named "webalizer.hist", stored in the output directory being

 49 # used.  The name can include a path, which will be relative to the output

 50 # directory unless absolute (starts with a leading '/')

 54 # Incremental processing allows multiple partial log files to be used

 55 # instead of one huge one.  Useful for large sites that have to rotate

 56 # their log files more than once a month.  The Webalizer will save its

 57 # internal state before exiting, and restore it the next time run, in

 58 # order to continue processing where it left off.  This mode also causes

 59 # The Webalizer to scan for and ignore duplicate records (records already

 60 # processed by a previous run).  See the README file for additional

 61 # information.  The value may be 'yes' or 'no', with a default of 'no'.

 62 # The file 'webalizer.current' is used to store the current state data,

 63 # and is located in the output directory of the program (unless changed

 64 # with the IncrementalName option below).  Please read at least the section

 65 # on Incremental processing in the README file before you enable this option

 69 # IncrementalName allows you to specify the filename for saving the

 70 # incremental data in.  It is similar to the HistoryName option where the

 71 # name is relative to the specified output directory, unless an absolute

 72 # filename is specified.  The default is a file named "webalizer.current"

 73 # kept in the normal output directory.  If you don't specify "Incremental"

 74 # as 'yes' then this option has no meaning.