혹시나 해서 jsm583 칩으로 만들어진 리뷰안 m.2 to USB3.0을 이용해서 사용이 가능한가 했는데 역시나(?) 안되는 듯.
usb 자체가 pcie bridge로 작동하는게 아니라 usb storage class로 잡혀 버리는 듯.
[338494.964509] usb 2-3: new SuperSpeed USB device number 4 using xhci_hcd [338494.977488] usb 2-3: New USB device found, idVendor=152d, idProduct=0583, bcdDevice= 2.13 [338494.977506] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [338494.977513] usb 2-3: Product: RevuAhn UX981 [338494.977519] usb 2-3: Manufacturer: RevuAhn [338494.977524] usb 2-3: SerialNumber: DD56419883F0D [338495.034745] usbcore: registered new interface driver usb-storage [338495.041007] scsi host0: uas [338495.041138] usbcore: registered new interface driver uas [338495.041650] scsi 0:0:0:0: Direct-Access RevuAhn UX981 0213 PQ: 0 ANSI: 6 [338495.043619] sd 0:0:0:0: Attached scsi generic sg0 type 0 [338504.393782] sd 0:0:0:0: [sda] Unit Not Ready [338504.393801] sd 0:0:0:0: [sda] Sense Key : Hardware Error [current] [338504.393815] sd 0:0:0:0: [sda] ASC=0x44 <<vendor>>ASCQ=0x81 [338504.520396] sd 0:0:0:0: [sda] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK [338504.520415] sd 0:0:0:0: [sda] Sense Key : Hardware Error [current] [338504.520427] sd 0:0:0:0: [sda] ASC=0x44 <<vendor>>ASCQ=0x81 [338504.646381] sd 0:0:0:0: [sda] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK [338504.646398] sd 0:0:0:0: [sda] Sense Key : Hardware Error [current] [338504.646411] sd 0:0:0:0: [sda] ASC=0x44 <<vendor>>ASCQ=0x81 [338504.690523] sd 0:0:0:0: [sda] 0 512-byte logical blocks: (0 B/0 B) [338504.690528] sd 0:0:0:0: [sda] 0-byte physical blocks [338504.812434] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled [338504.857011] sd 0:0:0:0: [sda] Asking for cache data failed [338504.857031] sd 0:0:0:0: [sda] Assuming drive cache: write through [338504.857041] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes not a multiple of physical block size (0 bytes) [338504.857049] sd 0:0:0:0: [sda] Optimal transfer size 33553920 bytes not a multiple of physical block size (0 bytes) [338504.857933] sd 0:0:0:0: [sda] Attached SCSI disk
PCIe Bridge는 맞지.. storage solution 이라 그렇지...(!!)
JMicron announced its JMS583 (USB 3.1 to PCIe Bridge controller) received USB-IF Logo Certification
The JMS583 is mainly used in the development of PCIe/NVMe related products, such as converting a PCIe/NVMe SSD to a superspeed plus USB interface portable mobile storage solution.
This will significantly reduce the cost and time needed for PCIe/NVMe SSD production in the factory, which will also accelerate the end-product’s time-to-market. JMicron believes that the market will always strive for extreme high-speed, low power consumption, thin and light solutions for external storage products.
Complies with PCI Express Base Specification Revision 3.1a ◼ Complies with NVM Express 1.3 ◼ Complies with USB 3.1 Gen 1 and Gen 2 Specification, USB Mass Storage Class, Bulk-Only Transport Specification (Revision 1.0) ◼ Complies with USB Attached SCSI Protocol (UASP) Specification (Revision 4)
Summary OpenVINO™ version that supports MYRIAD device.
Description Unable to determine whether MYRIAD device is supported on OpenVINO™ 2022.3.0.
Resolution Intel® Movidius ™ VPU based products (MYRIAD device) are not supported in OpenVINO™ 2022.3.0 release but will be added back in a future OpenVINO™ 2022.3.1 LTS update.
It basically depends on the GPU architecture. In pascal architecture 1TFLOP = 4TOPS. OK, so by that comparison NVIDIA Jetson Nano is doing about 2 TOPS