구차니의 잡동사니 모음

U-Boot 2017.05-15377-gedb23d4 (Aug 24 2017 - 07:09:51 -0300) for ODROID-XU4

CPU:   Exynos5422 @ 800 MHz

Model: Odroid XU4 based on EXYNOS5422

Board: Odroid XU4 based on EXYNOS5422

Type:  xu4

DRAM:  2 GiB

MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 1

MMC Device 0 ( SD ): 14.8 GiB

mmc_init: -5, time 4

*** Warning - bad CRC, using default environment

In:    serial

Out:   serial

Err:   serial

Net:   No ethernet found.

Press quickly 'Enter' twice to stop autoboot:  0

Exynos5422 #

Exynos5422 #

Exynos5422 #

Exynos5422 # pri

arch=arm

baudrate=115200

board=odroid

board_adc_value=1287

board_name=xu4

board_rev=1

boardname=odroidxu4

boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}

boot_device=SD

boot_efi_binary=load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootarm.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi

boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf

boot_net_usb_start=usb start

boot_prefixes=/ /boot/

boot_script_dhcp=boot.scr.uimg

boot_scripts=boot.scr.uimg boot.scr

boot_targets=mmc1 mmc0 usb0 pxe dhcp

bootargs=fb_x_res=1280 fb_y_res=720 vout=hdmi led_blink=1 hdmi_phy_res=720p60hz edid=0, hpd=1 disable_vu7=false touch_invert_x=false touch_invert_y=false

bootcmd=cfgload;movi r k 0 40008000;bootz 40008000

bootcmd_dhcp=run boot_net_usb_start; if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; setenv efi_old_vci ${bootp_vci};setenv efi_old_arch ${bootp_arch};setenv bootp_vci PXEClient:Arch:00010:UNDI:003000;setenv bootp_arch 0xa;if dhcp ${kernel_addr_r}; then tftpboot ${fdt_addr_r} dtb/${efi_fdtfile};if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r}; else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi;fi;setenv bootp_vci ${efi_old_vci};setenv bootp_arch ${efi_old_arch};setenv efi_fdtfile;setenv efi_old_arch;setenv efi_old_vci;

bootcmd_mmc0=setenv devnum 0; run mmc_boot

bootcmd_mmc1=setenv devnum 1; run mmc_boot

bootcmd_pxe=run boot_net_usb_start; dhcp; if pxe get; then pxe boot; fi

bootcmd_usb0=setenv devnum 0; run usb_boot

bootdelay=1

bootm_size=0x10000000

console=console=ttySAC2,115200n8

copy_uboot_emmc2sd=mmc dev 0;emmc open 0;mmc read  ${loadaddr} 0x0000 0x07de;emmc close 0;mmc dev 1;  mmc write ${loadaddr} 0x0001 0x07de;mmc dev 0;mmc dev 1;  mmc write ${loadaddr} 0x07df 0x0020;mmc dev 0

copy_uboot_sd2emmc=mmc dev 0;mmc read  ${loadaddr} 0x0001 0x07de;mmc dev 1;emmc open  1;mmc write ${loadaddr} 0x0000 0x07de;emmc close 1;mmc dev 0;mmc dev 1;  mmc write ${loadaddr} 0x07df 0x0020;mmc dev 0

cpu=armv7

dfu_alt_info=Autoset by THOR/DFU command run.

dfu_alt_system=uImage fat 0 1;zImage fat 0 1;Image.itb fat 0 1;uInitrd fat 0 1;boot.scr fat 0 1;boot.cmd fat 0 1;exynos5422-odroidxu3.dtb fat 0 1;exynos5422-odroidxu3-lite.dtb fat 0 1;exynos5422-odroidxu4.dtb fat 0 1;boot part 0 1;root part 0 2

distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done

efi_dtb_prefixes=/ /dtb/ /dtb/current/

env_erase=mw.l ${loadaddr} 0 4000;mmc dev 0;  mmc write ${loadaddr} 0x07df 0x0020;mmc dev 0

fdt_addr_r=0x43000000

fdtcontroladdr=b9920170

fdtfile=exynos5422-odroidxu4.dtb

kernel_addr_r=0x42000000

load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}

loadaddr=0x50000000

mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run scan_dev_for_boot_part; fi

mmcbootdev=0

mmcbootpart=1

mmcrootdev=0

mmcrootpart=2

pxefile_addr_r=0x51000000

ramdisk_addr_r=0x43300000

rootfstype=ext4

scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;

scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done

scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootarm.efi; then echo Found EFI removable media binary efi/boot/bootarm.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile

scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi

scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done

scriptaddr=0x50000000

soc=exynos

soc_id=5422

soc_rev=0.1

stderr=serial

stdin=serial

stdout=serial

usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi

vendor=samsung

Environment size: 4995/16380 bytes

Exynos5422 # ▒ 

U-Boot 2017.05-15377-gedb23d4 (Aug 24 2017 - 07:09:51 -0300) for ODROID-XU4

CPU:   Exynos5422 @ 800 MHz

Model: Odroid XU4 based on EXYNOS5422

Board: Odroid XU4 based on EXYNOS5422

Type:  xu4

DRAM:  2 GiB

MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 1

MMC Device 0 ( SD ): 14.8 GiB

mmc_init: -5, time 4

*** Warning - bad CRC, using default environment

In:    serial

Out:   serial

Err:   serial

Net:   No ethernet found.

Press quickly 'Enter' twice to stop autoboot:  0

reading boot.ini

9671 bytes read in 14 ms (673.8 KiB/s)

cfgload: applying boot.ini...

cfgload: setenv initrd_high "0xffffffff"

cfgload: setenv fdt_high "0xffffffff"

cfgload: setenv macaddr "00:1e:06:61:7a:39"

cfgload: setenv vout "hdmi"

cfgload: setenv cecenable "false" # false or true

cfgload: setenv disable_vu7 "false" # false

cfgload: setenv ddr_freq 825

cfgload: setenv external_watchdog "false"

cfgload: setenv external_watchdog_debounce "3"

cfgload: setenv HPD "true"

cfgload: setenv bootrootfs "console=tty1 console=ttySAC2,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0"

cfgload: fatload mmc 0:1 0x40008000 zImage

reading zImage

5671272 bytes read in 324 ms (16.7 MiB/s)

cfgload: fatload mmc 0:1 0x42000000 uInitrd

reading uInitrd

12243214 bytes read in 694 ms (16.8 MiB/s)

cfgload: setenv fdtloaded "false"

cfgload: if test "x${board_name}" = "x"; then setenv board_name "xu4"; fi

cfgload: if test "${board_name}" = "xu4"; then fatload mmc 0:1 0x44000000 exynos5422-odroidxu4.dtb; setenv fdtloaded "true"; fi

reading exynos5422-odroidxu4.dtb

63776 bytes read in 9 ms (6.8 MiB/s)

cfgload: if test "${board_name}" = "xu3"; then fatload mmc 0:1 0x44000000 exynos5422-odroidxu3.dtb; setenv fdtloaded "true"; fi

cfgload: if test "${board_name}" = "xu3l"; then fatload mmc 0:1 0x44000000 exynos5422-odroidxu3-lite.dtb; setenv fdtloaded "true"; fi

cfgload: if test "${fdtloaded}" = "false"; then fatload mmc 0:1 0x44000000 exynos5422-odroidxu4.dtb; setenv fdtloaded "true"; fi

cfgload: fdt addr 0x44000000

cfgload: setenv hdmi_phy_control "HPD=${HPD} vout=${vout}"

cfgload: if test "${cecenable}" = "false"; then fdt rm /cec@101B0000; fi

libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND

cfgload: if test "${disable_vu7}" = "false"; then setenv hid_quirks "usbhid.quirks=0x0eef:0x0005:0x0004"; fi

cfgload: if test "${external_watchdog}" = "true"; then setenv external_watchdog "external_watchdog=${external_watchdog} external_watchdog_debounce=${external_watchdog_debounce}"; fi

cfgload: setenv bootargs "${bootrootfs} ${videoconfig} ${hdmi_phy_control} ${hid_quirks} smsc95xx.macaddr=${macaddr} ${external_watchdog}"

cfgload: dmc ${ddr_freq}

cfgload: bootz 0x40008000 0x42000000 0x44000000

Kernel image @ 0x40008000 [ 0x000000 - 0x568968 ]

## Loading init Ramdisk from Legacy Image at 42000000 ...

   Image Name:   uInitrd

   Image Type:   ARM Linux RAMDisk Image (uncompressed)

   Data Size:    12243150 Bytes = 11.7 MiB

   Load Address: 00000000

   Entry Point:  00000000

   Verifying Checksum ... OK

## Flattened Device Tree blob at 44000000

   Booting using the fdt blob at 0x44000000

   Using Device Tree in place at 44000000, end 4401291f

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x100

[    0.000000] Linux version 4.14.69-148 (root@ba3e5121f23a) (gcc version 7.3.0 (Ubuntu/Linaro 7.3.0-16ubuntu3)) #1 SMP PREEMPT Mon Sep 10 13:07:55 -03 2018

[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d

[    0.000000] CPU: div instructions available: patching division code

[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[    0.000000] OF: fdt: Machine model: Hardkernel Odroid XU4

[    0.000000] Memory policy: Data cache writealloc

[    0.000000] cma: Reserved 128 MiB at 0xb6800000

[    0.000000] Samsung CPU ID: 0xe5422001

[    0.000000] Running under secure firmware.

[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x418 with crng_init=0

[    0.000000] percpu: Embedded 17 pages/cpu @eed65000 s37452 r8192 d23988 u69632

[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928

[    0.000000] Kernel command line: console=tty1 console=ttySAC2,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0  HPD=true vout=hdmi usbhid.quirks=0x0eef:0x0005:0x0004 smsc95xx.macaddr=00:1e:06:61:7a:39 false s5p_mfc.mem=16M

[    0.000000] hdmi: using HDMI mode

[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

[    0.000000] Memory: 1898372K/2074624K available (8192K kernel code, 655K rwdata, 2348K rodata, 1024K init, 326K bss, 45180K reserved, 131072K cma-reserved, 1157120K highmem)

[    0.000000] Virtual kernel memory layout:

[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)

[    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)

[    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)

[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)

[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)

[    0.000000]       .text : 0xc0008000 - 0xc0900000   (9184 kB)

[    0.000000]       .init : 0xc0c00000 - 0xc0d00000   (1024 kB)

[    0.000000]       .data : 0xc0d00000 - 0xc0da3c38   ( 656 kB)

[    0.000000]        .bss : 0xc0dab39c - 0xc0dfcee0   ( 327 kB)

[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1

[    0.000000] hperf_hmp: fast CPUs mask: 000000F0

[    0.000000] hperf_hmp: slow CPUs mask: 0000000F

[    0.000000] Preemptible hierarchical RCU implementation.

[    0.000000]  Tasks RCU enabled.

[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16

[    0.000000] GIC: Using split EOI/Deactivate mode

[    0.000000] Switching to timer-based delay loop, resolution 41ns

[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns

[    0.000007] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns

[    0.000030] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 49

[    0.001608] Console: colour dummy device 80x30

[    0.002258] console [tty1] enabled

[    0.002300] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)

[    0.002341] pid_max: default: 32768 minimum: 301

[    0.002531] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)

[    0.002571] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)

[    0.003424] CPU: Testing write buffer coherency: ok

[    0.004339] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100

[    0.020052] Setting up static identity map for 0x40100000 - 0x40100060

[    0.020671] ARM CCI driver probed

[    0.020903] Exynos MCPM support installed

[    0.027992] Hierarchical SRCU implementation.

[    0.043993] smp: Bringing up secondary CPUs ...

[    0.072374] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101

[    0.096334] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102

[    0.124327] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103

[    0.152377] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000

[    0.172358] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001

[    0.180652] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002

[    0.188662] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003

[    0.188815] smp: Brought up 1 node, 8 CPUs

[    0.188966] SMP: Total of 8 processors activated (384.00 BogoMIPS).

[    0.188989] CPU: All CPU(s) started in HYP mode.

[    0.189009] CPU: Virtualization extensions available.

[    0.190823] devtmpfs: initialized

[    0.207641] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0

[    0.207799] hperf_hmp: registered cpufreq transition notifier

[    0.207990] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns

[    0.208024] futex hash table entries: 2048 (order: 5, 131072 bytes)

[    0.210786] pinctrl core: initialized pinctrl subsystem

[    0.212946] NET: Registered protocol family 16

[    0.218386] DMA: preallocated 1024 KiB pool for atomic coherent allocations

[    0.224438] cpuidle: using governor menu

[    0.225237] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.

[    0.225263] hw-breakpoint: maximum watchpoint size is 8 bytes.

[    0.233649] exynos-audss-clk 3810000.audss-clock-controller: epll 180633609

[    0.256359] EXYNOS5420 PMU initialized

[    0.299281] usbcore: registered new interface driver usbfs

[    0.299347] usbcore: registered new interface driver hub

[    0.299518] usbcore: registered new device driver usb

[    0.299966] i2c-gpio soc:i2c-hdmi: using pins 177 (SDA) and 178 (SCL)

[    0.300542] s3c-i2c 12c70000.i2c: slave address 0x00

[    0.300568] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz

[    0.300821] s3c-i2c 12c70000.i2c: i2c-1: S3C I2C adapter

[    0.301322] media: Linux media interface: v0.10

[    0.301370] Linux video capture interface: v2.00

[    0.301480] pps_core: LinuxPPS API ver. 1 registered

[    0.301499] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>

[    0.301759] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled

[    0.302593] Advanced Linux Sound Architecture Driver Initialized.

[    0.303824] clocksource: Switched to clocksource mct-frc

[    0.363217] VFS: Disk quotas dquot_6.6.0

[    0.363298] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[    0.376926] NET: Registered protocol family 2

[    0.377511] TCP established hash table entries: 8192 (order: 3, 32768 bytes)

[    0.377602] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)

[    0.377768] TCP: Hash tables configured (established 8192 bind 8192)

[    0.377882] UDP hash table entries: 512 (order: 2, 16384 bytes)

[    0.377931] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)

[    0.378144] NET: Registered protocol family 1

[    0.378811] RPC: Registered named UNIX socket transport module.

[    0.378833] RPC: Registered udp transport module.

[    0.378851] RPC: Registered tcp transport module.

[    0.378868] RPC: Registered tcp NFSv4.1 backchannel transport module.

[    0.379069] Trying to unpack rootfs image as initramfs...

[    0.667837] random: fast init done

[    1.027520] Freeing initrd memory: 11960K

[    1.029054] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available

[    1.030021] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available

[    1.033486] audit: initializing netlink subsys (disabled)

[    1.033710] audit: type=2000 audit(1.028:1): state=initialized audit_enabled=0 res=1

[    1.034283] Initialise system trusted keyrings

[    1.034476] workingset: timestamp_bits=14 max_order=19 bucket_order=5

[    1.041786] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    1.042651] NFS: Registering the id_resolver key type

[    1.042684] Key type id_resolver registered

[    1.042702] Key type id_legacy registered

[    1.042731] nfs4filelayout_init: NFSv4 File Layout Driver Registering...

[    1.042782] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.

[    1.047713] Key type asymmetric registered

[    1.047735] Asymmetric key parser 'x509' registered

[    1.047799] bounce: pool size: 64 pages

[    1.047908] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)

[    1.048126] io scheduler noop registered

[    1.048148] io scheduler deadline registered

[    1.048400] io scheduler cfq registered (default)

[    1.048421] io scheduler mq-deadline registered

[    1.048439] io scheduler kyber registered

[    1.048678] io scheduler bfq registered

[    1.051046] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator

[    1.052079] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator

[    1.052175] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator

[    1.052547] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus not found, using dummy regulator

[    1.052630] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus-boost not found, using dummy regulator

[    1.057445] dma-pl330 3880000.adma: Loaded driver for PL330 DMAC-241330

[    1.057472] dma-pl330 3880000.adma:  DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6

[    1.060106] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330

[    1.060133] dma-pl330 121a0000.pdma:         DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32

[    1.062732] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330

[    1.062758] dma-pl330 121b0000.pdma:         DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32

[    1.063595] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330

[    1.063621] dma-pl330 10800000.mdma:         DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32

[    1.128113] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled

[    1.130364] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 58, base_baud = 0) is a S3C6400/10

[    1.130779] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 59, base_baud = 0) is a S3C6400/10

[    1.131163] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 60, base_baud = 0) is a S3C6400/10

[    2.030244] console [ttySAC2] enabled

[    2.034228] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10

[    2.044884] exynos-mixer 14450000.mixer: Linked as a consumer to 14650000.sysmmu

[    2.050899] iommu: Adding device 14450000.mixer to group 0

[    2.057936] exynos-hdmi 14530000.hdmi: Failed to get supply 'vdd': -517

[    2.063799] exynos-drm-g2d 10850000.g2d: Linked as a consumer to 10a60000.sysmmu

[    2.070584] exynos-drm-g2d 10850000.g2d: Linked as a consumer to 10a70000.sysmmu

[    2.077903] iommu: Adding device 10850000.g2d to group 1

[    2.083511] exynos-drm-g2d 10850000.g2d: The Exynos G2D (ver 4.1) successfully probed.

[    2.092130] exynos-rot 11c00000.rotator: Linked as a consumer to 11d40000.sysmmu

[    2.098432] iommu: Adding device 11c00000.rotator to group 2

[    2.104384] exynos-rot 11c00000.rotator: The exynos rotator is probed successfully

[    2.112369] exynos-drm-ipp exynos-drm-ipp: drm ipp registered successfully.

[    2.122759] mali 11800000.mali: Continuing without Mali regulator control

[    2.128879] mali 11800000.mali: GPU identified as 0x0620 r0p1 status 0

[    2.135105] mali 11800000.mali: Protected mode not available

[    2.140667] devfreq devfreq0: Couldn't update frequency transition information.

[    2.148256] mali 11800000.mali: Probed as mali0

[    2.161688] brd: module loaded

[    2.163938] libphy: Fixed MDIO Bus: probed

[    2.167672] usbcore: registered new interface driver r8152

[    2.172882] usbcore: registered new interface driver cdc_ether

[    2.178691] usbcore: registered new interface driver cdc_subset

[    2.186568] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[    2.191682] ehci-exynos: EHCI EXYNOS driver

[    2.196197] exynos-ehci 12110000.usb: EHCI Host Controller

[    2.201295] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1

[    2.209233] exynos-ehci 12110000.usb: irq 80, io mem 0x12110000

[    2.227874] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00

[    2.232709] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[    2.239208] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    2.246395] usb usb1: Product: EHCI Host Controller

[    2.251242] usb usb1: Manufacturer: Linux 4.14.69-148 ehci_hcd

[    2.257080] usb usb1: SerialNumber: 12110000.usb

[    2.262207] hub 1-0:1.0: USB hub found

[    2.265409] hub 1-0:1.0: 3 ports detected

[    2.270268] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[    2.275520] ohci-exynos: OHCI EXYNOS driver

[    2.279897] exynos-ohci 12120000.usb: USB Host Controller

[    2.285060] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2

[    2.292770] exynos-ohci 12120000.usb: irq 80, io mem 0x12120000

[    2.360105] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001

[    2.365453] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    2.373831] usb usb2: Product: USB Host Controller

[    2.377406] usb usb2: Manufacturer: Linux 4.14.69-148 ohci_hcd

[    2.383209] usb usb2: SerialNumber: 12120000.usb

[    2.388344] hub 2-0:1.0: USB hub found

[    2.391531] hub 2-0:1.0: 3 ports detected

[    2.397704] mousedev: PS/2 mouse device common for all mice

[    2.403177] i2c /dev entries driver

[    2.421022] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV

[    2.443666] vdd_sd: Bringing 3300000uV into 2800000-2800000uV

[    2.466519] vdd_ldo30: Bringing 1800000uV into 3300000-3300000uV

[    3.538073] s5m-rtc s2mps14-rtc: rtc core: registered s5m-rtc as rtc0

[    3.546976] s5p-jpeg 11f50000.jpeg: Linked as a consumer to 11f10000.sysmmu

[    3.552559] iommu: Adding device 11f50000.jpeg to group 3

[    3.558233] s5p-jpeg 11f50000.jpeg: encoder device registered as /dev/video30

[    3.565149] s5p-jpeg 11f50000.jpeg: decoder device registered as /dev/video31

[    3.572083] s5p-jpeg 11f50000.jpeg: Samsung S5P JPEG codec

[    3.577745] s5p-jpeg 11f60000.jpeg: Linked as a consumer to 11f20000.sysmmu

[    3.584522] iommu: Adding device 11f60000.jpeg to group 4

[    3.590195] s5p-jpeg 11f60000.jpeg: encoder device registered as /dev/video32

[    3.597115] s5p-jpeg 11f60000.jpeg: decoder device registered as /dev/video33

[    3.604059] s5p-jpeg 11f60000.jpeg: Samsung S5P JPEG codec

[    3.610595] s5p-mfc 11000000.codec: Linked as a consumer to 11200000.sysmmu

[    3.616575] s5p-mfc 11000000.codec: Linked as a consumer to 11210000.sysmmu

[    3.623440] iommu: Adding device 11000000.codec to group 5

[    3.646549] s5p-mfc 11000000.codec: preallocated 16 MiB buffer for the firmware and context buffers

[    3.654260] (NULL device *): Direct firmware load for s5p-mfc-v8.fw failed with error -2

[    3.662232] s5p_mfc_load_firmware:73: Firmware is not present in the /lib/firmware directory nor compiled in kernel

[    3.672796] s5p-mfc 11000000.codec: decoder registered as /dev/video10

[    3.679277] s5p-mfc 11000000.codec: encoder registered as /dev/video11

[    3.688097] exynos-gsc 13e00000.video-scaler: Linked as a consumer to 13e80000.sysmmu

[    3.694535] iommu: Adding device 13e00000.video-scaler to group 6

[    3.701813] exynos-gsc 13e10000.video-scaler: Linked as a consumer to 13e90000.sysmmu

[    3.708402] iommu: Adding device 13e10000.video-scaler to group 7

[    3.739969] thermal thermal_zone0: failed to read out thermal zone (-22)

[    3.746126] thermal thermal_zone1: failed to read out thermal zone (-22)

[    3.752838] thermal thermal_zone2: failed to read out thermal zone (-22)

[    3.759520] thermal thermal_zone3: failed to read out thermal zone (-22)

[    3.766217] thermal thermal_zone4: failed to read out thermal zone (-22)

[    3.772671] device-mapper: uevent: version 1.0.3

[    3.776846] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com

[    3.799150] sdhci: Secure Digital Host Controller Interface driver

[    3.803890] sdhci: Copyright(c) Pierre Ossman

[    3.808395] Synopsys Designware Multimedia Card Interface Driver

[    3.814766] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.

[    3.821099] dwmmc_exynos 12200000.mmc: Using internal DMA controller.

[    3.827446] dwmmc_exynos 12200000.mmc: Version ID is 250a

[    3.832837] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 83,64 bit host data width,64 deep fifo

[    3.842238] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq

[    3.868300] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)

[    3.896202] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.

[    3.901653] dwmmc_exynos 12220000.mmc: Using internal DMA controller.

[    3.908053] dwmmc_exynos 12220000.mmc: Version ID is 250a

[    3.913430] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 84,64 bit host data width,64 deep fifo

[    3.944298] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)

[    3.972890] ledtrig-cpu: registered to indicate activity on CPUs

[    3.981174] s5p-secss 10830000.sss: s5p-sss driver registered

[    3.985847] hidraw: raw HID events driver (C) Jiri Kosina

[    3.998962] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp

[    4.004229] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp

[    4.010819] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp

[    4.017406] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp

[    4.028371] NET: Registered protocol family 17

[    4.031343] NET: Registered protocol family 15

[    4.035840] Key type dns_resolver registered

[    4.040383] Registering SWP/SWPB emulation handler

[    4.045197] registered taskstats version 1

[    4.048894] Loading compiled-in X.509 certificates

[    4.059194] Key type encrypted registered

[    4.080429] OF: graph: no port node found in /soc/hdmi@14530000

[    4.085745] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations

[    4.092742] exynos-drm exynos-drm: bound 14450000.mixer (ops 0xc0966064)

[    4.099284] exynos-drm exynos-drm: bound 14530000.hdmi (ops 0xc0966704)

[    4.105863] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).

[    4.112445] [drm] No driver support for vblank timestamp query.

[    4.194114] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)

[    4.194998] NOHZ: local_softirq_pending 40

[    4.195007] NOHZ: local_softirq_pending 40

[    4.195020] NOHZ: local_softirq_pending 40

[    4.195142] mmc1: new ultra high speed DDR50 SDHC card at address aaaa

[    4.195475] mmcblk1: mmc1:aaaa SU16G 14.8 GiB

[    4.206465] NOHZ: local_softirq_pending 40

[    4.206525]  mmcblk1: p1 p2

[    4.292896] Console: switching to colour frame buffer device 240x67

[    4.353681] exynos-drm exynos-drm: fb0:  frame buffer device

[    4.359658] [drm] Initialized exynos 1.0.0 20110530 for exynos-drm on minor 0

[    4.368305] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller

[    4.372382] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 3

[    4.380250] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x02010010

[    4.388717] xhci-hcd xhci-hcd.3.auto: irq 150, io mem 0x12000000

[    4.394772] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002

[    4.401402] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    4.408601] usb usb3: Product: xHCI Host Controller

[    4.413435] usb usb3: Manufacturer: Linux 4.14.69-148 xhci-hcd

[    4.419245] usb usb3: SerialNumber: xhci-hcd.3.auto

[    4.424395] hub 3-0:1.0: USB hub found

[    4.427841] hub 3-0:1.0: 1 port detected

[    4.431913] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller

[    4.437192] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 4

[    4.444824] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0  SuperSpeed

[    4.451461] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.

[    4.459569] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003

[    4.466222] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    4.473414] usb usb4: Product: xHCI Host Controller

[    4.478250] usb usb4: Manufacturer: Linux 4.14.69-148 xhci-hcd

[    4.484062] usb usb4: SerialNumber: xhci-hcd.3.auto

[    4.489199] hub 4-0:1.0: USB hub found

[    4.492649] hub 4-0:1.0: 1 port detected

[    4.500452] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller

[    4.506361] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 5

[    4.514672] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x02010010

[    4.523854] xhci-hcd xhci-hcd.6.auto: irq 151, io mem 0x12400000

[    4.530423] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002

[    4.537654] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    4.545302] usb usb5: Product: xHCI Host Controller

[    4.550587] usb usb5: Manufacturer: Linux 4.14.69-148 xhci-hcd

[    4.556824] usb usb5: SerialNumber: xhci-hcd.6.auto

[    4.562373] hub 5-0:1.0: USB hub found

[    4.566521] hub 5-0:1.0: 1 port detected

[    4.570965] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller

[    4.576823] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 6

[    4.584887] xhci-hcd xhci-hcd.6.auto: Host supports USB 3.0  SuperSpeed

[    4.591970] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.

[    4.600585] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003

[    4.607841] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    4.615539] usb usb6: Product: xHCI Host Controller

[    4.620909] usb usb6: Manufacturer: Linux 4.14.69-148 xhci-hcd

[    4.627251] usb usb6: SerialNumber: xhci-hcd.6.auto

[    4.632908] hub 6-0:1.0: USB hub found

[    4.637151] hub 6-0:1.0: 1 port detected

[    4.642448] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling

[    4.648541] rtc rtc1: invalid alarm value: 1900-1-1 0:0:0

[    4.654494] s3c-rtc 101e0000.rtc: rtc core: registered s3c as rtc1

[    4.662234] exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz)

[    4.671415] exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz)

[    4.680291] exynos-bus: new bus device registered: soc:bus_fsys_apb (200000 KHz ~ 200000 KHz)

[    4.689516] exynos-bus: new bus device registered: soc:bus_fsys (200000 KHz ~ 200000 KHz)

[    4.698479] exynos-bus: new bus device registered: soc:bus_fsys2 ( 75000 KHz ~ 150000 KHz)

[    4.707559] exynos-bus: new bus device registered: soc:bus_mfc ( 96000 KHz ~ 333000 KHz)

[    4.716490] exynos-bus: new bus device registered: soc:bus_gen ( 89000 KHz ~ 267000 KHz)

[    4.725290] exynos-bus: new bus device registered: soc:bus_peri ( 67000 KHz ~  67000 KHz)

[    4.734298] exynos-bus: new bus device registered: soc:bus_g2d ( 84000 KHz ~ 333000 KHz)

[    4.743160] exynos-bus: new bus device registered: soc:bus_g2d_acp ( 67000 KHz ~ 267000 KHz)

[    4.752376] exynos-bus: new bus device registered: soc:bus_jpeg ( 75000 KHz ~ 300000 KHz)

[    4.761323] exynos-bus: new bus device registered: soc:bus_jpeg_apb ( 84000 KHz ~ 167000 KHz)

[    4.770560] exynos-bus: new bus device registered: soc:bus_disp1_fimd (120000 KHz ~ 200000 KHz)

[    4.780030] exynos-bus: new bus device registered: soc:bus_disp1 (120000 KHz ~ 300000 KHz)

[    4.789007] exynos-bus: new bus device registered: soc:bus_gscl_scaler (150000 KHz ~ 300000 KHz)

[    4.798562] exynos-bus: new bus device registered: soc:bus_mscl ( 84000 KHz ~ 400000 KHz)

[    4.807411] samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory

[    4.815778] samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory

[    4.824664] odroid-audio sound: multicodec <-> 3830000.i2s mapping ok

[    4.834691] s5m-rtc s2mps14-rtc: setting system clock to 2000-01-01 00:00:31 UTC (946684831)

[    4.848366] ALSA device list:

[    4.851646]   #0: Odroid-XU4

[    4.855893] Freeing unused kernel memory: 1024K

Loading, please wait...

starting version 237

[    4.959901] usb 3-1: new high-speed USB device number 2 using xhci-hcd

[    5.116453] usb 3-1: New USB device found, idVendor=05e3, idProduct=0610

[    5.123634] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[    5.131240] usb 3-1: Product: USB2.0 Hub

[    5.135612] usb 3-1: Manufacturer: GenesysLogic

[    5.156041] hub 3-1:1.0: USB hub found

[    5.160785] hub 3-1:1.0: 2 ports detected

[    5.239992] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd

[    5.266594] usb 4-1: New USB device found, idVendor=05e3, idProduct=0616

[    5.273636] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[    5.281131] usb 4-1: Product: USB3.0 Hub

[    5.285362] usb 4-1: Manufacturer: GenesysLogic

[    5.300106] hub 4-1:1.0: USB hub found

[    5.305001] hub 4-1:1.0: 2 ports detected

[    5.307865] NOHZ: local_softirq_pending 80

[    5.342136] NOHZ: local_softirq_pending 40

[    5.354094] NOHZ: local_softirq_pending 40

[    5.369219] NOHZ: local_softirq_pending 40

[    5.380316] NOHZ: local_softirq_pending 40

[    5.395657] NOHZ: local_softirq_pending 40

[    5.487917] usb 3-1.1: new low-speed USB device number 3 using xhci-hcd

[    5.599724] usb 3-1.1: New USB device found, idVendor=046d, idProduct=c077

[    5.606812] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[    5.614303] usb 3-1.1: Product: USB Optical Mouse

[    5.619193] usb 3-1.1: Manufacturer: Logitech

[    5.639636] input: Logitech USB Optical Mouse as /devices/platform/soc/soc:usb3-0/12000000.dwc3/xhci-hcd.3.auto/usb3/3-1/3-1.1/3-1.1:1.0/0003:046D:C077.0001/input/input0

[    5.655322] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.3.auto-1.1/input0

[    5.668523] usbcore: registered new interface driver usbhid

[    5.674429] usbhid: USB HID core driver

[    5.715850] usb 3-1.2: new low-speed USB device number 4 using xhci-hcd

[    5.831946] usb 6-1: new SuperSpeed USB device number 2 using xhci-hcd

[    5.847351] usb 3-1.2: New USB device found, idVendor=05af, idProduct=0802

[    5.854643] usb 3-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[    5.860524] usb 6-1: New USB device found, idVendor=0bda, idProduct=8153

[    5.860530] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6

[    5.860536] usb 6-1: Product: USB 10/100/1000 LAN

[    5.860540] usb 6-1: Manufacturer: Realtek

[    5.860544] usb 6-1: SerialNumber: 000001000000

[    5.891269] usb 3-1.2: Product: USB Keyboard

[    5.895842] usb 3-1.2: Manufacturer:

[    5.933107] input:   USB Keyboard as /devices/platform/soc/soc:usb3-0/12000000.dwc3/xhci-hcd.3.auto/usb3/3-1/3-1.2/3-1.2:1.0/0003:05AF:0802.0002/input/input1

[    6.003990] hid-generic 0003:05AF:0802.0002: input,hidraw1: USB HID v1.10 Keyboard [  USB Keyboard] on usb-xhci-hcd.3.auto-1.2/input0

[    6.029563] input:   USB Keyboard as /devices/platform/soc/soc:usb3-0/12000000.dwc3/xhci-hcd.3.auto/usb3/3-1/3-1.2/3-1.2:1.1/0003:05AF:0802.0003/input/input2

[    6.048077] usb 6-1: reset SuperSpeed USB device number 2 using xhci-hcd

[    6.103975] hid-generic 0003:05AF:0802.0003: input,hidraw2: USB HID v1.10 Device [  USB Keyboard] on usb-xhci-hcd.3.auto-1.2/input1

[    6.112847] r8152 6-1:1.0 eth0: v1.09.9

Begin: Loading essential drivers ... done.

Begin: Running /scripts/init-premount ... done.

Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.

Begin: Running /scripts/local-premount ... done.

Begin: Will now check root file system ... fsck from util-linux 2.31.1

[/sbin/fsck.ext4 (1) -- /dev/mmcblk1p2] fsck.ext4 -y -C0 /dev/mmcblk1p2

e2fsck 1.44.1 (24-Mar-2018)

rootfs was not cleanly unmounted, check forced.

Pass 1: Checking inodes, blocks, and sizes

Deleted inode 138150 has zero dtime.  Fix? yes

Pass 2: Checking directory structure

[   11.261291] random: crng init done===================         / 84.2%

Pass 3: Checking directory connectivity

Pass 4: Checking reference counts

Pass 5: Checking group summary information

Block bitmap differences:  -(1096832--1096907)

Fix? yes

Free blocks count wrong for group #33 (7400, counted=7476).

Fix? yes

Free blocks count wrong (2598459, counted=2580934).

Fix? yes

Inode bitmap differences:  -138150

Fix? yes

Free inodes count wrong for group #16 (169, counted=170).

Fix? yes

Free inodes count wrong (793895, counted=791875).

Fix? yes

rootfs: ***** FILE SYSTEM WAS MODIFIED *****

rootfs: 174781/966656 files (0.4% non-contiguous), 1275322/3856256 blocks

fsck exited with status code 1

done.

[   14.704558] EXT4-fs (mmcblk1p2): mounted filesystem without journal. Opts: (null)

done.

Begin: Running /scripts/local-bottom ... done.

Begin: Running /scripts/init-bottom ... done.

[   15.147344] systemd[1]: System time before build time, advancing clock.

[   15.251419] NET: Registered protocol family 10

[   15.257454] Segment Routing with IPv6

[   15.265693] ip_tables: (C) 2000-2006 Netfilter Core Team

[   15.292868] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)

[   15.317986] systemd[1]: Detected architecture arm.

Welcome to Ubuntu 18.04.1 LTS!

[   15.357018] systemd[1]: Set hostname to <odroid>.

[   15.962362] systemd[1]: Reached target Swap.

[  OK  ] Reached target Swap.

[   15.979929] systemd[1]: Reached target User and Group Name Lookups.

[  OK  ] Reached target User and Group Name Lookups.

[   16.004045] systemd[1]: Started Forward Password Requests to Wall Directory Watch.

[  OK  ] Started Forward Password Requests to Wall Directory Watch.

[   16.028446] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.

[  OK  ] Set up automount Arbitrary Executab…rmats File System Automount Point.

[   16.055905] systemd[1]: Reached target Remote File Systems.

[  OK  ] Reached target Remote File Systems.

[   16.076294] systemd[1]: Created slice System Slice.

[  OK  ] Created slice System Slice.

[   16.096209] systemd[1]: Created slice system-serial\x2dgetty.slice.

[  OK  ] Created slice system-serial\x2dgetty.slice.

[  OK  ] Listening on Journal Audit Socket.

[  OK  ] Listening on udev Control Socket.

[  OK  ] Listening on udev Kernel Socket.

[  OK  ] Listening on Journal Socket.

         Starting Uncomplicated firewall...

[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.

         Starting udev Coldplug all Devices...

[  OK  ] Listening on fsck to fsckd communication Socket.

         Mounting Kernel Debug File System...

[  OK  ] Created slice User and Session Slice.

[  OK  ] Reached target Slices.

         Starting Set the console keyboard layout...

[  OK  ] Listening on Syslog Socket.

         Starting Load Kernel Modules...

         Starting Remount Root and Kernel File Systems...

         Starting Create list of required st…ce nodes for the current kernel.[   16.385107] EXT4-fs (mmcblk1p2): re-mounted. Opts: errors=remount-ro

..

[  OK  ] Listening on Journal Socket (/dev/log).

         Starting Journal Service...

         Mounting POSIX Message Queue File System...

[  OK  ] Created slice system-systemd\x2dfsck.slice.

[  OK  ] Started Uncomplicated firewall.

[  OK  ] Mounted Kernel Debug File System.

[  OK  ] Started Set the console keyboard layout.

[FAILED] Failed to start Load Kernel Modules.

See 'systemctl status systemd-modules-load.service' for details.

[  OK  ] Started Journal Service.

[  OK  ] Started Remount Root and Kernel File Systems.

[  OK  ] Started Create list of required sta…vice nodes for the current kernel.

[  OK  ] Mounted POSIX Message Queue File System.

         Starting Create Static Device Nodes in /dev...

         Starting Load/Save Random Seed...

         Starting Flush Journal to Persistent Storage...

         Starting Apply Kernel Variables...

         Mounting Kernel Configuration File System...

[  OK  ] Started Create Static Device Nodes in /dev.

[  OK  ] Started Load/Save Random Seed.

[  OK  ] Started Apply Kernel Variables.

[  OK  ] Mounted Kernel Configuration File System.

[  OK  ] Reached target Local File Systems (Pre).

         Starting udev Kernel Device Manager...

[  OK  ] Started udev Coldplug all Devices.

[  OK  ] Started Flush Journal to Persistent Storage.

[  OK  ] Started udev Kernel Device Manager.

[  OK  ] Started Dispatch Password Requests to Console Directory Watch.

[  OK  ] Reached target Local Encrypted Volumes.

[  OK  ] Found device /dev/ttySAC2.

[  OK  ] Reached target Sound Card.

[  OK  ] Found device /dev/disk/by-label/boot.

         Starting File System Check on /dev/disk/by-label/boot...

[  OK  ] Started File System Check Daemon to report status.

[  OK  ] Started File System Check on /dev/disk/by-label/boot.

         Mounting /media/boot...

[  OK  ] Mounted /media/boot.

[  OK  ] Reached target Local File Systems.

         Starting Create Volatile Files and Directories...

         Starting Tell Plymouth To Write Out Runtime Data...

         Starting Raise network interfaces...

         Starting Set console font and keymap...

[  OK  ] Started Create Volatile Files and Directories.

[  OK  ] Started Tell Plymouth To Write Out Runtime Data.

[  OK  ] Started Set console font and keymap.

         Starting Update UTMP about System Boot/Shutdown...

         Starting Network Name Resolution...

         Starting Network Time Synchronization...

[  OK  ] Started Update UTMP about System Boot/Shutdown.

[  OK  ] Started Raise network interfaces.

[  OK  ] Started Network Name Resolution.

[  OK  ] Started Network Time Synchronization.

[  OK  ] Reached target System Time Synchronized.

[  OK  ] Reached target System Initialization.

[  OK  ] Started Daily Cleanup of Temporary Directories.

[  OK  ] Started Trigger anacron every hour.

[  OK  ] Started Daily apt download activities.

[  OK  ] Started Daily apt upgrade and clean activities.

[  OK  ] Started Discard unused blocks once a week.

[  OK  ] Listening on CUPS Scheduler.

[  OK  ] Listening on D-Bus System Message Bus Socket.

[  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.

         Starting Socket activation for snappy daemon.

[  OK  ] Started CUPS Scheduler.

[  OK  ] Reached target Paths.

[  OK  ] Started Message of the Day.

[  OK  ] Reached target Timers.

[  OK  ] Reached target Host and Network Name Lookups.

[  OK  ] Listening on Socket activation for snappy daemon.

[  OK  ] Reached target Sockets.

[  OK  ] Reached target Basic System.

         Starting Disk Manager...

[  OK  ] Started CUPS Scheduler.

[  OK  ] Started Regular background program processing daemon.

         Starting System Logging Service...

         Starting Dispatcher daemon for systemd-networkd...

         Starting Accounts Service...

         Starting Snappy daemon...

[  OK  ] Started D-Bus System Message Bus.

         Starting WPA supplicant...

         Starting Restore /etc/resolv.conf i…fore the ppp link was shut down...

         Starting LSB: Speech Dispatcher...

[  OK  ] Started Set the CPU Frequency Scaling governor.

         Starting Save/Restore Sound Card State...

         Starting Network Manager...

         Starting LSB: Load kernel modules needed to enable cpufreq scaling...

         Starting Modem Manager...

         Starting Initialize hardware monitoring sensors...

[  OK  ] Started Run anacron jobs.

         Starting Login Service...

         Starting LSB: automatic crash report generation...

         Starting Avahi mDNS/DNS-SD Stack...

[  OK  ] Started System Logging Service.

[  OK  ] Started Snappy daemon.

[  OK  ] Started WPA supplicant.

[  OK  ] Started Save/Restore Sound Card State.

         Starting Authorization Manager...

         Starting Wait until snapd is fully seeded...

[  OK  ] Started Avahi mDNS/DNS-SD Stack.

[  OK  ] Started Make remote CUPS printers available locally.

[  OK  ] Started Login Service.

[  OK  ] Started Wait until snapd is fully seeded.

[  OK  ] Started Restore /etc/resolv.conf if…before the ppp link was shut down.

[  OK  ] Started Initialize hardware monitoring sensors.

[  OK  ] Started Authorization Manager.

[  OK  ] Started Accounts Service.

[  OK  ] Started LSB: Speech Dispatcher.

[  OK  ] Started LSB: automatic crash report generation.

[  OK  ] Started Disk Manager.

[  OK  ] Started Modem Manager.

         Starting Hostname Service...

[  OK  ] Started LSB: Load kernel modules needed to enable cpufreq scaling.

         Starting LSB: set CPUFreq kernel parameters...

[  OK  ] Started Dispatcher daemon for systemd-networkd.

[  OK  ] Started LSB: set CPUFreq kernel parameters.

[  OK  ] Started Hostname Service.

[  OK  ] Started Network Manager.

         Starting Network Manager Script Dispatcher Service...

         Starting Network Manager Wait Online...

[  OK  ] Reached target Network.

[  OK  ] Started Unattended Upgrades Shutdown.

         Starting OpenVPN service...

         Starting OpenBSD Secure Shell server...

         Starting Permit User Sessions...

[  OK  ] Started OpenVPN service.

[  OK  ] Started Permit User Sessions.

[  OK  ] Started Network Manager Script Dispatcher Service.

         Starting Light Display Manager...

[  OK  ] Started OpenBSD Secure Shell server.

[  OK  ] Started Light Display Manager.

[  OK  ] Started Network Manager Wait Online.

[  OK  ] Reached target Network is Online.

         Starting /etc/rc.local Compatibility...

         Starting LSB: disk temperature monitoring daemon...

[  OK  ] Started crash report submission daemon.

         Starting Tool to automatically coll… submit kernel crash signatures...

         Starting ODROID Specific System Tweaks...

[  OK  ] Started /etc/rc.local Compatibility.

         Starting Hold until boot process finishes up...

[  OK  ] Started Hold until boot process finishes up.

[  OK  ] Started ODROID Specific System Tweaks.

[  OK  ] Started Tool to automatically colle…nd submit kernel crash signatures.

         Starting Set console scheme...

[  OK  ] Started Serial Getty on ttySAC2.

[  OK  ] Started LSB: disk temperature monitoring daemon.

[  OK  ] Started Set console scheme.

[  OK  ] Created slice system-getty.slice.

[  OK  ] Started Getty on tty1.

[  OK  ] Reached target Login Prompts.

[  OK  ] Reached target Multi-User System.

[  OK  ] Reached target Graphical Interface.

         Starting Update UTMP about System Runlevel Changes...

[  OK  ] Started Update UTMP about System Runlevel Changes.

Ubuntu 18.04.1 LTS odroid ttySAC2

odroid login:

[    **] A stop job is running for Session c1 of user odroid (17s / 1min 30s) 

Ubuntu 18.04.1 LTS odroid ttySAC2

         Stopping Session c1 of user odroid.

[  OK  ] Stopped target Sound Card.

[  OK  ] Stopped target Timers.

[  OK  ] Stopped Daily apt upgrade and clean activities.

[  OK  ] Stopped Discard unused blocks once a week.

[  OK  ] Stopped Daily apt download activities.

         Stopping User Manager for UID 1000...

         Stopping Save/Restore S         Stopping Unattended Upgrades Shutdown...

[  OK  ] Stopped Initialize hardware monitoring sensors.

         Stopping LSB: disk temperature monitoring daemon...

         Stopping LSB: set CPUFreq kernel parameters...

         Stopping Accounts Service...

         Stopping LSB: Speech Dispatcher...

         Stopping Make remote CUPS printers available locally...

[  OK  ] Stopped Daily Cleanup of Temporary Directories.

         Stopping Modem Manager...

         Stopping OpenBSD Secure Shell server...

         Stopping Daemon for power management...

         Stopping Light Display Manager...

         Stopping Disk Manager...

         Stopping LSB: automatic crash report generation...

[  OK  ] Stopped OpenVPN service.

         Stopping Dispatcher daemon for systemd-networkd...

[  OK  ] Stopped Trigger anacron every hour.

[  OK  ] Unmounted /run/user/1000/gvfs.

[  OK  ] Stopped Disk Manager.

[  OK  ] Stopped Regular background program processing daemon.

[  OK  ] Stopped System Logging Service.

[  OK  ] Stopped Dispatcher daemon for systemd-networkd.

[  OK  ] Stopped Accounts Service.

[  OK  ] Stopped Snappy daemon.

[  OK  ] Stopped Modem Manager.

[  OK  ] Stopped Authorization Manager.

[  OK  ] Stopped Make remote CUPS printers available locally.

[  OK  ] Stopped Light Display Manager.

[  OK  ] Stopped OpenBSD Secure Shell server.

[  OK  ] Stopped crash report submission daemon.

[  OK  ] Stopped Serial Getty on ttySAC2.

[  OK  ] Stopped Getty on tty1.

[  OK  ] Stopped User Manager for UID 1000.

[  OK  ] Stopped RealtimeKit Scheduling Policy Service.

[  OK  ] Stopped Daemon for power management.

[  OK  ] Stopped Save/Restore Sound Card State.

[  OK  ] Stopped Unattended Upgrades Shutdown.

[  OK  ] Stopped Tool to automatically colle…nd submit kernel crash signatures.

[  OK  ] Stopped target System Time Synchronized.

[  OK  ] Stopped target Host and Network Name Lookups.

[  OK  ] Removed slice system-getty.slice.

[  OK  ] Stopped /etc/rc.local Compatibility.

[  OK  ] Removed slice system-serial\x2dgetty.slice.

         Stopping CUPS Scheduler...

         Stopping Avahi mDNS/DNS-SD Stack...

[  OK  ] Stopped Avahi mDNS/DNS-SD Stack.

[  OK  ] Stopped LSB: disk temperature monitoring daemon.

[  OK  ] Stopped LSB: set CPUFreq kernel parameters.

[  OK  ] Stopped LSB: Speech Dispatcher.

         Stopping LSB: Load kernel modules needed to enable cpufreq scaling...

[  OK  ] Stopped target Network is Online.

[  OK  ] Stopped Network Manager Wait Online.

[  OK  ] Stopped LSB: Load kernel modules needed to enable cpufreq scaling.

[  OK  ] Stopped LSB: automatic crash report generation.

[  OK  ] Stopped CUPS Scheduler.

[    **] A stop job is running for Session c1 of user odroid (17s / 1min 28s)

[  OK  ] Stopped Session c1 of user odroid.

[  OK  ] Removed slice User Slice of odroid.

         Stopping Permit User Sessions...

         Stopping Login Service...

[  OK  ] Stopped Permit User Sessions.

[  OK  ] Stopped target Remote File Systems.

[  OK  ] Stopped target Network.

         Stopping Raise network interfaces...

         Stopping Network Name Resolution...

         Stopping Network Manager...

         Stopping WPA supplicant...

[  OK  ] Stopped Network Name Resolution.

[  OK  ] Stopped WPA supplicant.

[  OK  ] Stopped Network Manager.

[  OK  ] Stopped Login Service.

[  OK  ] Stopped Raise network interfaces.

[  OK  ] Stopped target User and Group Name Lookups.

         Stopping D-Bus System Message Bus...

[  OK  ] Stopped D-Bus System Message Bus.

[  OK  ] Stopped target Basic System.

[  OK  ] Stopped target Slices.

[  OK  ] Removed slice User and Session Slice.

[  OK  ] Stopped target Sockets.

[  OK  ] Closed Socket activation for snappy daemon.

[  OK  ] Closed Syslog Socket.

[  OK  ] Closed Avahi mDNS/DNS-SD Stack Activation Socket.

[  OK  ] Closed CUPS Scheduler.

[  OK  ] Stopped target Paths.

[  OK  ] Stopped CUPS Scheduler.

[  OK  ] Closed D-Bus System Message Bus Socket.

[  OK  ] Stopped target System Initialization.

         Stopping Load/Save Random Seed...

         Stopping Update UTMP about System Boot/Shutdown...

[  OK  ] Stopped Apply Kernel Variables.

[  OK  ] Stopped target Local Encrypted Volumes.

[  OK  ] Stopped Forward Password Requests to Wall Directory Watch.

[  OK  ] Stopped Dispatch Password Requests to Console Directory Watch.

         Stopping Network Time Synchronization...

[  OK  ] Stopped Load/Save Random Seed.

[  OK  ] Stopped Network Time Synchronization.

[  OK  ] Stopped Update UTMP about System Boot/Shutdown.

[  OK  ] Stopped Create Volatile Files and Directories.

[  OK  ] Stopped target Local File Systems.

         Unmounting /run/user/1000...

         Unmounting /media/boot...

[  OK  ] Unmounted /run/user/1000.

[  OK  ] Stopped target Swap.

[  OK  ] Unmounted /media/boot.

[  OK  ] Reached target Unmount All Filesystems.

[  OK  ] Stopped File System Check on /dev/disk/by-label/boot.

[  OK  ] Removed slice system-systemd\x2dfsck.slice.

[  OK  ] Stopped target Local File Systems (Pre).

[  OK  ] Stopped Remount Root and Kernel File Systems.

[  OK  ] Stopped Create Static Device Nodes in /dev.

[  OK  ] Reached target Shutdown.

[  OK  ] Reached target Final Step.

         Starting Power-Off...

[  453.371533] reboot: Power down

[  453.373459] syscon_poweroff : offset = 0x330c, value = 0x5200, mask = 0xffffffff

▒