option byte를 설정하고 알아서 reconnect 하는데 이때 리부팅이 되는것 같긴하다.
| ./STM32_Programmer_CLI -c port=SWD -ob DBANK=1 -d ~/STM32CubeIDE/stm32g473/stm32g476/Debug/stm32g476.elf -v -rst ------------------------------------------------------------------- STM32CubeProgrammer v2.21.0 ------------------------------------------------------------------- ST-LINK SN : 35FF72064D53373233492143 ST-LINK FW : V2J45S7 Board : -- Voltage : 3.25V SWD freq : 4000 KHz Connect mode: Normal Reset mode : Software reset Device ID : 0x469 Revision ID : Rev X Device name : STM32G47x/G48x/G414 Flash size : 256 KBytes Device type : MCU Device CPU : Cortex-M4 BL Version : 0xD5 Debug in Low Power mode enabled UPLOADING OPTION BYTES DATA ... Bank : 0x00 Address : 0x40022020 Size : 20 Bytes [==================================================] 100% Bank : 0x01 Address : 0x40022044 Size : 16 Bytes [==================================================] 100% Bank : 0x02 Address : 0x40022070 Size : 8 Bytes [==================================================] 100% PROGRAMMING OPTION BYTES AREA ... Bank : 0x00 Address : 0x40022020 Size : 20 Bytes [==================================================] 100% Reconnecting... Reconnected ! UPLOADING OPTION BYTES DATA ... Bank : 0x00 Address : 0x40022020 Size : 20 Bytes [==================================================] 100% Bank : 0x01 Address : 0x40022044 Size : 16 Bytes [==================================================] 100% Bank : 0x02 Address : 0x40022070 Size : 8 Bytes [==================================================] 100% OPTION BYTE PROGRAMMING VERIFICATION: Option Bytes successfully programmed Time elapsed during option Bytes configuration: 00:00:01.187 Opening and parsing file: stm32g476.elf Memory Programming ... File : stm32g476.elf Size : 18.32 KB Address : 0x08000000 Erasing memory corresponding to segment 0: Erasing internal memory sectors [0 9] Download in Progress: [==================================================] 100% File download complete Time elapsed during download operation: 00:00:00.589 Verifying... Read progress: [==================================================] 100% Time elapsed during verifying operation: 00:00:00.120 Download verified successfully MCU Reset Software reset is performed |
도움말
| $ ./STM32_Programmer_CLI ------------------------------------------------------------------- STM32CubeProgrammer v2.21.0 ------------------------------------------------------------------- Usage : STM32_Programmer_CLI.exe [command_1] [Arguments_1][[command_2] [Arguments_2]...] Generic commands: -?, -h, --help : Show this help -c, --connect : Establish connection to the device <port=<PortName> : Interface identifier. ex COM1, /dev/ttyS0, usb1, JTAG, SWD, JLINK...) USB port optional parameters: [sn=<serialNumber>] : Serial number of the usb dfu [PID=<Product ID>] : Product ID. ex: 0xA38F, etc, default 0xDF11 [VID=<Vendor ID>] : Vendor ID. ex: 0x0389, etc, default x0483 UART port optional parameters: [br=<baudrate>] : Baudrate. ex: 115200, 9600, etc, default 115200 [P=<parity>] : Parity bit, value in {NONE,ODD,EVEN}, default EVEN [db=<data_bits>] : Data bit, value in {6, 7, 8} ..., default 8 [sb=<stop_bits>] : Stop bit, value in {1, 1.5, 2} ..., default 1 [fc=<flowControl>] : Flow control Value in {OFF,Hardware,Software} ..., default OFF rts=<status> : low or high dtr=<status> : low or high Not supported for STM32MP [noinit=noinit_bit]: Set No Init bits, value in {0,1} ..., default 0 [console] : Enter UART console mode JTAG/SWD debug port optional parameters: [freq=<frequency>] : Frequency in KHz. Default frequencies: 4000 SWD 9000 JTAG with STLINKv2 8000 SWD 21333 with STLINKv3 [index=<index>] : Index of the debug probe. default index 0 [sn=<serialNumber>]: Serial Number of the debug probe [ap=<accessPort>] : Access Port index to connect to. default ap 0 [mode=<mode>] : Connection mode. Value in {UR/HOTPLUG/NORMAL/POWERDOWN/HWRSTPULSE} default mode: NORMAL [reset=<mode>] : Reset modes: SWrst/HWrst/Crst. Default mode: SWrst Reset mode with UR connection mode is HWrst [shared] : Enable shared mode allowing connection of two or more instances of STM32CubeProgrammer or other debugger to the same ST-LINK probe. [tcpport=<Port>] : Port used for running ST-Link Server, default 7184 [LPM] : Enable debug in Low Power mode(default mode) [dLPM] : Disable debug in Low Power mode [getAuthID] : Get device identification (Option only for STM32U5 series) [speed=<Reliable/fast>]: Choose flashing Reliable/fast (Option only for STM32U5 series) [TargetSel=<TargetSel>]: Specifies the target device by its Target Sel value SPI port optional parameters: [br=<baudrate>] : Baudrate. [cpha=<cpha_val>] : 1Edge or 2Edge. default 1Edge [cpol=<cpol_val>] : low or high [crc=<crc_val>] : enable or disable (0/1). [crcpol=<crc_pol>] : crc polynom value. [datasize=<size>] : 8bit/16bit [direction=<val>] : Direction: 2LFullDuplex/2LRxOnly/1LRx/1LTx [firstbit=<val>] : First Bit: MSB/LSB [frameformat=<val>]: Frame Format: Motorola/TI [mode=<val>] : Mode: master/slave [nss=<val>] : NSS: soft/hard [nsspulse=<val>] : NSS pulse: Pulse/NoPulse [delay=<val>] : Delay: Delay/NoDelay, delay of few microseconds [noinit=noinit_bit]: Set No Init bits, value in {0,1} ..., default 0 CAN port optional parameters: [br=<rbaudrate>] : Baudrate : 125, 250, 500, 1000 Kbps, default 125 [mode=<canmode>] : CAN Mode : NORMAL, LOOPBACK..., default NORMAL [ide=<type>] : CAN Type : STANDARD or EXTENDED, default STANDARD [rtr=<format>] : Frame Format: DATA or REMOTE, default DATA [fifo=<afifo>] : Msg Receive : FIFO0 or FIFO1, default FIFO0 [fm=<fmode] : Filter Mode : MASK or LIST, default MASK [fs=<fscale>] : Filter Scale: 16 or 32, default 32 [fe=<fenable>] : Filter Activation : ENABLE or DISABLE, default ENABLE [fbn=<fbanknb>] : Filter Bank Number : 0 to 13, default 0 [noinit=noinit_bit]: Set No Init bits, value in {0,1} ..., default 0 I2C port optional parameters: [add=<ownadd>] : Slave address : address in hex format [br=<sbaudrate>] : Baudrate : 100 or 400 Kbps, default 400 [sm=<smode>] : Speed Mode : STANDARD or FAST, default FAST [am=<addmode>] : Address Mode : 7 or 10 bits, default 7 [af=<afilter>] : Analog filter : ENABLE or DISABLE, default ENABLE [df=<dfilter>] : Digital filter : ENABLE or DISABLE, default DISABLE [dnf=<dnfilter>] : Digital noise filter : 0 to 15, default 0 [rt=<rtime>] : Rise time : 0-1000(STANDARD), 0-300(FAST), default 0 [ft=<ftime>] : Fall time : 0-300 (STANDARD), 0-300(FAST), default 0 [noinit=noinit_bit]: Set No Init bits, value in {0,1} ..., default 0 -version, --version : Displays the tool's version -l, --list : List all available communication interfaces <uart> : UART interface <usb> : USB interface <st-link> : st-link interface <stlink> <st-link-only> : Enumarte st-link list without connecting and intruse the target <stlink-only> Access port number is set to zero. <shared> : Allowing to list all boards connected to other instance(s) <stlink-shared> of STM32CubeProgrammer where the shared mode is enabled. -getTargetSelList : List all devices currently connected through SWD Multidrop -q, --quietMode : Enable quiet mode. No progress bar displayed -log, --log : Store the detailed output in log file [<file_Path.log>] : Path of the log file, default path = $HOME/.STM32Programmer/trace.log -vb, --verbosity : Specify verbosity level <Level> : Verbosity level, value in {1, 2, 3} -y, --yes : Ignore confirmation prompt message Available commands for STM32 MCU: --skipErase : Skip sector erase before programming -sl, --safelib : Add a segment into a firmware file (elf,bin hex,srec and s19) containing computed CRC values To use only with the safety lib component <file_path> : File path to be modified <start_address> : Flash memory start address <end_address> : Flash memory end address <slice_size> : Size of data per CRC value <pattern> : Optional pattern from 0x0 to 0xFF. Default pattern 0x00 -ms, --mergesbsfu : Add a binary header and a sbsfu segment to an elf file <elf_file_path> : File path to be modified <header_file_path> : Header file path <sbsfu_file_path> : SBSFU file path -e, --erase : Erase memory pages/sectors devices: Not supported for STM32MP [all] : Erase all sectors [<sectorsCodes>] : Erase the specified sectors identified by sectors codes. ex: 0, 1, 2 to erase sectors 0, 1 and 2 for EEPROM : ed1 & ed2 [<[start end]>] : Erase the specified sectors starting from start code to end code, ex: -e [5 10] -w, --write -d, --download : Download the content of a file into device memory <file_path> : File path name to be downloaded: (bin, hex, srec, s19 elf, stm32 or tsv file) [<address>] : Start address of download [incremental] : Optional, new write mechanism If the parameter [incremental] is not indicated, the tool will use the legacy write mechanism The new write mechanism programs only modified sectors to accelerate the flashing operation The legacy write mechanism programs the full firmware into flash memory -w32 : Write a 32-bits data into device memory <address> : Start address of download <32-bit_data> : 32-bit data to be downloaded values should be separated by space -w16 : Write a 16-bits data into device memory <address> : Start address of download <16-bit_data> : 16-bit data to be downloaded values should be separated by space -w8 : Write a 8-bits data into device memory <address> : Start address of download <8-bit_data> : 8-bit data to be downloaded values should be separated by space -v, --verify : Verify if the programming operation is achieved successfully [fast] : Optional, new verify mechanism If the parameter [fast] is not indicated, the tool will use the legacy verify mechanism The new verify mechanism verifies the integrity of data sector per sector The legacy verify mechanism verifies the integrity of data byte per byte -nv, --noverify : Do not verify if the programming operation is achieved successfully, used with -w32/-w16/-w8 commands -checksum, --checksum : Memory checksum calculation <address> : Optional, Start address <size> : Optional, Size of memory region : If the parameters <address> and <size> are not indicated, the tool will calculate the full internal Flash -r32 : Read a 32-bit data from device memory <address> : Read start address <size> : Size of data -r16 : Read a 16-bit data from device memory <address> : Read start address <size> : Size of data -r8 : Read a 8-bit data from device memory <address> : Read start address <size> : Size of data -rst : Reset system -hardRst : Hardware reset -rstbl : Reset Bootloader Available only with JTAG/SWD debug port -halt : Halt core -run : Run core -step : Step core Available only with JTAG/SWD debug port -score : Get core status Available only with JTAG/SWD debug port -coreReg : Read/Write core registers [<core_register>] R0/../R15/PC/LR/PSP/MSP/XPSR/APSR/IPSR/EPSR/ PRIMASK/BASEPRI/FAULTMASK/CONTROL [core_reg=<value>] value in case of write opration Note: multiple registers can be handled at once Available only with JTAG/SWD debug port -r, --read -u, --upload : Upload the device memory content to a .bin/.hex/.srec/.s19 file <address> : Start address of read and upload <size> : Size of memory content to be read <file_path> : file path with .bin/.hex/.srec/.s19 extension -el, --extload : Select a custom external memory-loader for JTAG/SWD <file_path> : External memory-loader file path -elbl, --extloadbl : Select a custom external memory-loader for Bootloader interface (SFIx only) <file_path> : External memory-loader file path -s, --start -g, --go : Run the code at the specified address. [<address>] : Start address -rdu, --readunprotect: Remove memory's Read Protection by shifting the RDP level from level 1 to level 0. -tzenreg, --tzenregression: Remove TrustZone Protection by disabling the TZEN from 1 to 0. -ob, --optionbytes : This command allows the user to manipulate the device 's OptionBytes by displaying or modifying them. [displ] : This option allows the user to display the whole set of Option Bytes. [unlockchip] : This option allows the user to unlock the chip in case of bad Option Bytes already programmed. [OptByte=<value>] : This option allows the user to program the given Option Byte. -force_no_da, --force_no_da : Froce OB programming if the DA is not already configured. Available only for STM32H50x devices -noreconnect, --noreconnect : Programming OB without performing a reconnect -w32dbgmcu : Write a 32-bits data into DBGMCU DBG AUTH HOST register <32-bit_data> 32-bit data to be downloaded, only for STM32H5xx devices. -lockRDP1, -setOEM1KEY : Lock RDP level 1 <LSB> : OEM1 least significant bytes key <MSB> : OEM1 most significant bytes key -unlockRDP1 : Unlock RDP level 1 <LSB> : OEM1 least significant bytes key <MSB> : OEM1 most significant bytes key -lockRDP2, -setOEM2KEY : Lock RDP level 2 <LSB> : OEM2 least significant bytes key <MSB> : OEM2 most significant bytes key -unlockRDP2 : Unlock RDP level 2 <LSB> : OEM2 least significant bytes key <MSB> : OEM2 most significant bytes key -ssigfoxc : Save the chip Certificate, supported for STM32WL devices <file_path> : Certificate file path -wsigfoxc : Write the Sigfox credential, supported for STM32WL devices <file_path> : Certificate file path (binary, header) <address> : start address for write -fillmemory : Fill memory with the given pattern from the chosen address. <start_address> : Start address for write. The address 0x08000000 is used by default [size=<value>] : Size of the data to write [pattern=<value>] : The pattern value to write. [dataWidth=8|16|32]: The filling data size: 8 bits is selected by default. -blankcheck : Verifies that the STM32 Flash memory is blank. If the Flash memory is not blank, the first address with data is highlighted in a message. -fchecksum, --file-checksum : File checksum calculation <file_path> : File path Beta commands: -regdump : Read and dump Core and MCU registers <file_path> : Log file path with extension .log or .txt [choice=<number>] : Device number from the list of compatible devices (optional), this list is displayed if the command is performed without this optional argument -hf : Hard fault analyzer Helps to identify system faults that occur when the CPU is driven into a fault condition by the application code. -pwr, --power : Perform power ON/OFF, only for STLINK supporting this capability <on/off> : Select the power type [index=<number>] : Index of the debug probe. -r32fast : Read a 32-bit data from device memory with direct access Only for accessible internal memories via ST-LINK interfaces <address> : Read start address <size> : Size of data Available commands for STM32 MPU: -c, --connect : Establish connection to the device <port=<PortName> : Interface identifer. ex COM1, /dev/ttyS0, usb1) USB port optional parameters: [sn=<serialNum>] : Serial number of the usb dfu [serial] : Activate USB serial Gadget for MPU devices UART port optional parameters: [br=<baudrate>] : Baudrate. ex: 115200, 9600, etc, default 115200 [P=<parity>] : Parity bit, value in {NONE,ODD,EVEN}, default NONE [db=<data_bits>] : Data bit, value in {6, 7, 8} ..., default 8 [sb=<stop_bits>] : Stop bit, value in {1, 1.5, 2} ..., default 1 [fc=<flowControl>] : Flow control (Not yet supported for STM32MP) Value in {OFF,Hardware,Software} ..., default OFF [noinit=noinit_bit]: Set No Init bits, value in {0,1} ..., default 0 -s, --start -g, --go : Run the code at the specified partition ID. [<partitionID>] : Partition ID If not specified, last loaded partition will be started [<startAdress>] : Start address If not specified, last loaded segment address [<noack>] : No acknowledgment required If not specified, acknowledgment will be required -detach : Send detach command to DFU -wb : Write blob <blob_file_path> : Blob file path -pmic : Program PMIC NVM <PMIC file_path> : PMIC file_path -gc, --getcertificate : Get the chip Certificate, supported for devices with security features <file_path> : Certificate file path into which the chip certificate will be uploaded <tfa-ssp-path> : Input TFA SSP signed firmware path. Used only with STM32MP1 devices -p, --phaseID : Display the current partition ID to be loaded -w, --write -d, --download : Download the content of a file into device memory <file_path> : File path name to be downloaded: (bin, stm32 file <partition_id> : Partition ID to be downloaded -rp, --readPart : Upload a memory partion ID content to a .bin file <partionID> : Partion to be read [<offset address>] : Offset address of read and upload <size> : Size of partion content to be read <file_path> : Binary file path -ssp, --ssp : Program an SSP file <ssp_file_path> : SSP file path to be programmed, bin or ssp extension <ssp-fw-path> : SSP signed firmware path [hsm=0|1] : Set user option for HSM use value in {0 (do not use HSM), 1 (use HSM)} Default value : hsm=0 <lic_path|slot=slotID> : Path to the license file (if hsm=0) or reader slot ID if HSM is used (hsm=1) plugin=<plugin-fw-path> : Optional, binary plugin firmware path. Used only with STM32MP2x devices -tm : Force timeout <value> : Number of milliseconds -rst : Reset USB device OTP commands : -otp displ : This command allows the user to display all or parts of the OTP structure [word=<id>] : {Optional} display a specific OTP registers {values and status} Up to 96 OTP words [0 to 95], id value in hex/dec format -otp write : This command allows to fuse or update OTP words Up to 96 OTP words [0 to 95] at the same command line [lock] : {Optional} indicate the operation type, update or permanent lock [word=<id>] : This field contains the OTP word number in hex/dec format [value=<value>] : Value to be written in hex format -otp lock : This command allows to fuse permanently OTP words Up to 96 OTP words [0 to 95] at the same command line [word=<id>] : This field contains the OTP word number in hex/dec format -otp fwrite : This command allows to program a binary file [lock] : {Optional} indicate the operation type, update or permanent lock <bin_path> : Binary file path, 32-bits aligned data [word=<id>] : OTP word number in hex/dec format, start word of program STM32WB0 series OTP store command: -storekeyotp , --storekeyotp : Store OTP key <key_path.c> : Folder with the public_key.c file to store in OTP <start_address> : Start FW address MCU Secure programming specific commands: -installipmodule, --installipmodule : Install ip module file <file_path> : Path of smu file to be programmed [hsm=0|1] : Set user option for HSM use value in {0 (do not use HSM), 1 (use HSM)} Default value : hsm=0 <lic_path|slot=slotID> : Path to the license file (if hsm=0) or reader slot ID if HSM is used (hsm=1) note that if it is the case of global license, please use hsm = 0 with license path. [<address>] : Destination address of the smu module -updateipmodule, --updateipmodule : update ip module. <file_path> : Path of SMU file containing the update. [<address>] : Destination address of the smu module -sfi, --sfi : Program an sfi file [<protocol=Ptype>] : Protocol type to be used : static/live Only static protocol is supported so far Default value static <file_path> : Path of sfi file to be programmed [hsm=0|1] : Set user option for HSM use value in {0 (do not use HSM), 1 (use HSM)} Default value : hsm=0 <lic_path|slot=slotID> : Path to the SFI license file (if hsm=0) or reader slot ID if HSM is used (hsm=1) -ssfi, --ssfi : Program an ssfi file <ssfi_file_path> : Path of ssfi file to be programmed <rsse_file_path> : RSSe file path -rsse, --rsse : Set the RSSe file path, supported for devices with security extension <file_path> : RSSe file path -mcsv, --mcsv : Set the MCSV file path indicating SFI's modules configuration supported for STM32H5xx devices <file_path> : MCSV file path with .mcsv extension -ecsv, --ecsv : Set the ECSV file path indicating SFI's external modules configuration supported for STM32H5xx devices <file_path> : ECSV file path with .ecsv extension -a, --abort : This command allows the user to clean a not properly finished process. The currently ongoing operation will stop and the system will return to idle state -dsecurity : Disable the security for STM32WL -setdefaultob : Set default Option Bytes for STM32WL -rssgetversion, --rssgetversion : get the version of RSS HSM related commands: -hsmgetinfo : Read the HSM available information [slot=<SlotID>] : Slot ID of the Smart Card Reader Default value: slot=1 (the PC integrated SC reader) -hsmgetcounter : Read the current value of the license counter [slot=<SlotID>] : Slot ID of the Smart Card Reader Default value: slot=1 (the PC integrated SC reader) -hsmgetfwid : Read the Firmware/Module Identifier [slot=<SlotID>] : Slot ID of the Smart Card Reader Default value: slot=1 (the PC integrated SC reader) -hsmgetstatus : Read the current card life-cycle state [slot=<SlotID>] : Slot ID of the Smart Card Reader Default value: slot=1 (the PC integrated SC reader) -hsmgetlicense : Get a license for the current chip if counter is not null <file_path> : File path into which the received license will be stored [slot=<SlotID>] : Slot ID of the Smart Card Reader Default value: slot=1 (the PC integrated SC reader) [protocol=<Ptype>] : Protocol type to be used : static/live Only static protocol is supported so far Default value static <tfa-ssp-path> : Input TFA SSP signed firmware path. Used only for STM32MP1 devices -hsmgetlicensefromcertifbin, -hsmglfcb : Get a license for the input certificate if counter is not null <certif_file_path.bin> : Input certificate file path <license_file_path.bin> : File path into which the received license will be stored [slot=<SlotID>] : Slot ID of the Smart Card Reader Default value: slot=1 (the PC integrated SC reader) [protocol=<Ptype>] : Protocol type to be used : static/live Only static protocol is supported so far Default value static STM32WBxx specific commands: -getuid64 : Read the device UID -fusgetstate : Read the FUS state -fusopgetversion : Read the FUS Operator version -antirollback : Perform the antirollback operation (Only on Bootloader interface) -startfus : Perform the startfus operation Firmware Upgrade commands: -fwdelete : Delete the BLE stack firmware -fwupgrade : Upgrade the BLE stack firmware or the FUS firmware <file_path> : New firmware image file path <address> : Start address of download [firstinstall=0|1] : 1 if it is a first install otherwise 0 optional, Default value: firstinstall=0 [startstack=0|1] : 1 to start the stack after the upgrade otherwise 0 optional, Default value: startstack=1 -v : Verify if the download operation is achieved successfully before starting upgrade -startwirelessstack : Start the wireless stack Key management commands: -authkeyupdate : Authentication key update <file_path> : New authentication key file path. : This is the public key generated by : STM32TrustedPackageCreator using -sign command. -authkeylock : Authentication key lock : Once locked, it's no longuer possible to change it : using authkeyupdate command -wusrkey : Write user key <file_path> : User key file path <keytype=1|2|3> : User key type, values : 1, 2 or 3. : 1 = simple key, 2 = master key, 3 = encrypted key. Serial Wire Viewer specific commands: -swv : Printf via SWO <freq=<frequency>> : System Clock in MHz <portnumber=0-31|all> : ITM port number, values : 0-31, or all for All ports [<file_Path.log>] : Path of the SWV log file (optional), : default path = $USER_HOME/STMicroelectronics/STM32Programmer/SWV_Log/swv.log -RA : Start the reception of swv automatically -startswv : Printf via SWO & Start the reception of swv automatically Script Manager command: -script : Start the execution of Script File <file_Path.prg> : Path of the script file (.prg) Provisionning Command: -sdp : Start the OBKey Provisioning <File_Path> : OBKey File Path Provisioning with password : -pwd : Start Provisioning with password value=<password_value> : Password value path=<password_path> : location of password file to be used in Debug Authentication Set Product State RSS Command: -psrss : Start the RSS Product State <Value> : An hexadecimal value Get Product State RSS Command: -psrss displ : Start the Get RSS Product State Option Bytes RSS Command: -obrss : Start the Option Bytes RSS Change <Value 1> <Value 2> <Value 3> <Value 4> : An hexadecimal values Debug Authentication options: [debugauth=<1|2>] : to choose starting authentication(1) or discovery(2) [pwd=<password_file_path>] : required in case of authentication with password [key=<key_file_path>] : required in case of authentication with certificate [cert=<certificate_file_path>] : required in case of authentication with certificate [per=<requested_permission>] : required in case of authentication with certificate. : Each permission is referred to by a specific letter and a numerical bit value. : Enable debugauth=2 to access the permissions list with bit numbers and letters. : Debug Authentication requires the selection of one specific permission. : Certain products also provide optional actions to choose from. Example:Forced Download Key Wrapping Command -rssekw : Set The Key Wrapping RSSe File Path supported for devices with security extension <file_path> : RSSe Key Wrapping file path <file_path> : Private Key .pem file path [Not to be added for ECC CPVK wrapping using DHUK or DHUK xOR BHK] <file_path> : Output .bin file path [KeyType=<eccchipfu|eccchiplu>] : The Type of the ECC Chip Key to wrap [ExportPublicKey=<Yes|No>] : Generate or Not the public Key [WrappingKeySelect=<DHUK|DHUK_XOR_BHK>] : Used Method to wrap the private key [KeyUsage=<ECDSA_USAGE_SIGN|ECC_USAGE_SCALAR_MUL>] : Usage of the private key [SecAttr=<SECURE|NON_SECURE>] : Secure or Non Secure context [PrivAttr=<PRIVILEGE|NON_PRIVILEGE>] : Privileged or Non Priviledged context [AESMode=<ECB|CBC|GCM>] : AES mode for wrapping with user Key |
'embeded > Cortex-M4 STM' 카테고리의 다른 글
| NUCLEO-WL55JC (0) | 2026.03.17 |
|---|---|
| stm32g473 ART accelerator on/off ? (0) | 2026.02.06 |
| stm32g473 flash doubleword (0) | 2026.02.04 |
| STM32G47x dual bank flash (0) | 2026.02.03 |
| STM32F429I-DISC1 with lvgl (0) | 2026.02.03 |
