Microsoft/Windows2009. 12. 8. 11:11
이녀석이 먼가해서 검색해봤더니
디스크가 동적 디스크가 되서 제대로 인식못해 생기는 거라는데
AHCI(SATA)와 연관이 된건가 해서 일단은 드라이버를 설치했는데 잘될지는 모르겠다 ㅠ.ㅠ

[링크 : http://blog.naver.com/quriquri2/150036739681] >> SESSION3_INITIALIZATION_FAILED
[링크 : http://nicebug.egloos.com/1525609] >> AHCI on XP



2009.12.9 추가
ACHI 설치후 부팅이 잘 안되는 문제는 해결되었으나,
그래픽 카드가 제대로 설치되었음에도 해상도/색상이 이상하게 설정되는 문제가 발생했다.
Posted by 구차니
하드웨어2009. 10. 9. 16:21
900번째 글을 이런내용으로 쓰게 되다니 ㄱ-




회사에 노트북을 포맷하려고 하는데
compaq nx6320 모델이다. 듀얼코어 / SATA 하드인데
XP를 하려고 하니 하드 인식 못한다고 버팅기고, BIOS는 워낙 단순해서 설정가능한 항목이 없다.
일단 SATA native mode 라는게 있는데, 졸음 갈아엎기 상태라서..
save가 제대로 되었었는지 확인을 못하고, 제대로 못해봤다. 다음번에 확실하게 확인하고
SATA native mode가 꺼졌는지 확인해 봐야겠다.

2009.10.28 추가
아래 스샷을 보면 알겠지만, HP BIOS에서 ESC는 변동사항을 취소한다.(cancel)
반드시 F10을 눌러서 Accept 하고 Save and Exit 한다.



[링크 : http://radmoon.egloos.com/1635349]
[링크 : http://animator.egloos.com/3267406]
[링크 : http://h50177.www5.hp.com/support/269843-999/howto/71234.html] << 요거 참고


Native Serial ATA Mode

The advanced features that can be utilized in native mode revolve around improvements to the Serial ATA interconnect. The feature that has generated the most interest in this area is hot plugging, which allows an end user to remove a storage device from a Serial ATA controller while a system is running. This is useful for RAID systems and notebook docking stations with built-in storage devices. However, hot plugging should not be attempted with a system's primary boot device.

Another improvement is finer grained power management. In addition to doing power management on Serial ATA storage devices, the Serial ATA controller itself can be managed so that unused parts of the controller can be put into lower power modes to conserve electricity.

Finally there are features for Serial ATA drivers. There are new control, error and status registers that allow the Serial ATA controller to pass information to the driver about Serial ATA specific features. Also the Serial ATA interconnect configures its own transfer rate so that the driver no longer needs to.


[링크 : http://www.microsoft.com/whdc/device/storage/serialATA_FAQ.mspx]








드라이버를 받아도 USB를 인식할지 미지수라서 드라이버 파일만 하기도 애매하고..


아무튼 AHCI 라는 녀석때문에 SATA를 인식못하는 것이므로
드라이버를 별도로 추가해주면 가능하다고는 한다.



결론.. 대세는 Windows7 이어야 하는 건가!


[링크 : http://jcas.co.kr/zbxe/108245]
[링크 : http://blog.daum.net/idrlee/16100066]

Posted by 구차니
Microsoft/Windows2008. 12. 26. 01:18
머하는 녀석인지 몰라도..
결론만 말하자면 이녀석을 켜 놓으면

WinXP로 설치시 하드를 인식 못한다.



확인 기종은 삼보 에버라텍 4600, SATA2 인데,
이녀석은 EIDE 용이 아닌 SATA 관련된 기능으로, BIOS 상에서도 WindowsXP 관련하여
XP 쓸경우 AHCI Support 를 Disable 하라고 해 놓았으니, 머.. 할말은 없다.

검색을 해보니

The Advanced Host Controller Interface (AHCI) is a hardware mechanism that allows software to communicate with Serial ATA (SATA) devices (such as host bus adapters) that are designed to offer features not offered by Parallel ATA (PATA) controllers, such as hot-plugging and native command queuing.

Common problems switching to AHCI under Windows

Enabling AHCI in a system's BIOS will cause a 0x7B Blue Screen of Death STOP error (INACCESSIBLE_BOOT_DEVICE) on installations of Windows XP where AHCI/RAID drivers for that system's chipset are not installed - i.e. boot failure.[citation needed] Switching the chipset to AHCI mode involves changing the BIOS settings and will not work. Usually, manual installation of new drivers is required before enabling AHCI in BIOS.[5] Alternatively, a "Repair" installation with the appropriate driver loaded during the setup process usually corrects the problem. For motherboards with more than one Sata controller (for example, some boards have Intel and Jmicron Sata controllers) another alternative is possible. The sata cable for the boot drive can be inserted into a port on one controller (which can be configured in IDE mode), allowing the machine to boot successfully with the other controller configured for AHCI mode. The AHCI drivers can then be installed in windows without difficulty before swapping the cable back.
  • For Intel chipsets (for example, Intel ICH9) drivers are available from either an OEM motherboard or computer manufacturer. For the Intel versions, the driver must be loaded before loading the OS (by pressing F6 as setup starts, then using the floppy disk when prompted).The Intel drivers will work for both XP and Vista. Also, in the case of ICH9, an unsupported method to enable AHCI on ICH9 is available.
  • When attempting to install Windows XP or a previous version on an AHCI-enabled system, setup will fail with the error message "setup could not detect hard disk drive..." since no drivers will be found for accessing the SATA controller/s. This problem can be corrected by either using a floppy disk or by slipstreaming the appropriate drivers into the Windows XP installation CD, or by turning on IDE emulation in the BIOS settings if it's available (usually labelled COMPATIBILITY or ACPI).
  • Enabling AHCI in a system with Windows Vista already installed will result in a BSoD if SATA was configured in IDE mode during Vista's installation. Before enabling AHCI in the BIOS, users must first follow the instructions found at Microsoft Knowledge Base article 922976.
  • Enabling AHCI in a system BIOS on installations of Windows XP or Windows Vista will cause SATA Optical drives to disappear. A Hotfix for Windows Vista is available under the title: "SATA optical drives are not available after you start a Windows Vista-based computer."[6] This problem was fixed in Vista SP1.

아마도 회사에서 에버라텍 4600 Vista 가 자꾸 죽는 이유가 다른게 아니라 AHCI 문제였던 것 같은데.. 부팅시에 죽는게 아니라 가동중에 이유없이(메신저 하거나, 네트워크 통해 복사 중) 죽는 것 봐서는 네트워크 드라이버 문제일 가능성이 좀더 높아 보이지만, 테스트 기간이 짧아서 확실하게 단언하긴 힘들다.
[출처 : http://en.wikipedia.org/wiki/Advanced_Host_Controller_Interface]


ACPI가 먼지 궁금해서 한번 찾아 봤다.

The Advanced Configuration and Power Interface (ACPI) specification is an open standard for unified operating system-centric device configuration and power management. ACPI, first released in December 1996, defines platform-independent interfaces for hardware discovery, configuration, power management and monitoring.
[출처 : http://en.wikipedia.org/wiki/Acpi]
Posted by 구차니