넌 또 왜 난리니 ㅠㅠ

집에 가서 odroid 가지고 놀고 끄고 다시 켜려는데

어라 한대가 갑자기 안켜진다?!?!?

아놔... 결국(?)에는 eMMC 랑 또 주말에 씨름해야 하나? ㅠㅠ

엌? 커널 업데이트 하다가 커널 날아갔나?

OK U-Boot 2010.12-svn (May 12 2014 - 15:05:46) for Exynox4412 CPU: S5PC220 [Samsung SOC on SMP Platform Base on ARM CortexA9] APLL = 1000MHz, MPLL = 880MHz DRAM:  2 GiB PMIC VERSION : 0x00, CHIP REV : 3 TrustZone Enabled BSP BL10version: 20121128 Checking Boot Mode ... EMMC4.41 REVISION: 2.0 Manufacture ID 0x11 [ 7456MB ] NAME: S5P_MSHC4 MMC Device 0: 7456 MB MMC Device 1: 14804 MB MMC Device 2 not found *** Warning - using default environment USB3503 NINT = OUTPUT0LOW! ModeKey Check... run normal_boot No ethernet found. Hit any0key to stop autoboot:  0 Exynos4412 # boot do_fat_cfgload : cmd = fatload mmc 0:1 0x41000000 boot.ini reading boot.ini ** Unable0to read file boot.ini ** NAME: S5P_MSHC4 NAME: S5P_MSHC4 >>> Load Boot Script from mmc 0:1 <<< reading boot.scr Warning : Reads a file that is smaller than the cluster size. 355 bytes read in 46 ms (6.8 KiB/s) ##0Executing script at 40008000 reading zImage ** Unable to read file zImage ** reading0uInitrd Warning : Reads a file that is smaller than the cluster size. 64 bytes read in 32 ms (2 KiB/s) ## Booting kernel from Legacy Image at 40008000 ...    Image0Name:  0   0Image Type:   ARM Linux Script (uncompressed)    Data Size:    291 Bytes = 291 Bytes   0Load Address: 00000000    Entry Point:  00000000    Contents:    0 0Image 0: 283 Bytes = 283 Bytes 0 0Verifying Checksum ... OK Wrong Image Type for bootm command ERROR: can't get kernel image! Exynos4412 #

+

커널 복사해줘도 자동 부팅 안되서

결론 에라이 걍 밀자 -_-

Exynos44120# pri baudrate=115200 bootargs=fb_x_res=1280 fb_y_res=720 hdmi_phy_res=720 bootcmd=    cfgload; mmc rescan 0:1; mmc rescan 0:2;  if run loadbootscript_1; bootdelay=1 bootscript=source 40008000 cfg_file_name=boot.ini cfg_load_base_mem=41000000 cfg_load_device=0 cfg_load_partition=1 cfg_load_partition_type=fat copy_uboot_emmc2sd=emmc open 0;movi r z f 0 40000000;emmc close 0;movi0w f 1 40; copy_uboot_sd2emmc=movi r f 0 40000000;emmc open 1;movi w z f 1 40000000;emmc c; default_bootcmd=echo0>>> Run Default Bootcmd <<<;movi read kernel 0 40008000;mo0 erase_uboot_env=mmc write 0 0x40008000 0x977 0x20; ethaddr=00:40:5c:26:0a:5b extra_arg_0=0 extra_arg_1=0 extra_arg_2=0 extra_arg_3=0 gatewayip=192.168.0.1 ipaddr=192.168.0.20 loadbootscript_1=echo >>> Load Boot Script from mmc 0:1 <<<;fatload mmc 0:1 400r loadbootscript_2=echo >>> Load Boot Script from mmc 0:2 <<<;fatload mmc 0:20400r netmask=255.255.255.0 serverip=192.168.0.10 usb_invert_clken=0 Environment size: 1706/16380 bytes

우찌된게..

시리얼만 꽂아 두기만 해도 부팅이 멈추지?