1. LED 깜박이기
어떤 분이 댓글로 Start Locating Drive 하면 불이 깜박일거라고 하셨는데 맞았다.
그 와중에 막 누르다 보니 도움말이 뜨는걸 뒤늦게 발견!
Dell은 일정시간 깜박이고 꺼지더니 이런건 좀 아쉽네
2. RAID 장치 번호
케이블을 보다보니 손댄적도 없는데 상단이 뒷번호가 할당되어 있는걸 뒤늦게 발견(!)
운영상의 차이일수도 있겠지만 혹시 모르니 메뉴얼은 찾아봐야 할 듯.
그래서 RAID card에 꽂히는 SAS 케이블을 두개 순서 바꾸어서 해결!
| smc2108 (0) | 2024.04.03 |
|---|---|
| SMC2108 SSD cachecade (0) | 2024.04.03 |
| MegaCLI (0) | 2024.04.01 |
| MegaRAID Storage Manager(MSM) 설치완료 (0) | 2024.04.01 |
| msm (megaraid) 관리 설치 실패 (0) | 2023.11.14 |
귀찮아서 RAID5로 대충 만들었는데 초기화 하는데 계속 에러가 올라와서 보니 한녀석이 완전 망가진듯
Media Error Count가 슝슝슝
근데...
2x4=8bay 인데
0,1,2,3
4,5,6,7
로 인식이 될 줄 알았는데
4,5,6,7
0,1,2,3
로 상하가 반대로 되었나 slot이 0,4,5,6,7로 뜬다. 메뉴얼 찾아는 봐야할 듯..
| SAS 1TB * 4 구매 (0) | 2024.04.11 |
|---|---|
| 3.5파이 이어폰 잭 저항이... (0) | 2024.04.09 |
| 컴퓨터 셋팅완료 (0) | 2024.03.20 |
| cpu, ram 적출 (0) | 2024.03.19 |
| 다이소 웹캠.. M12 렌즈.. 계륵?! (0) | 2024.03.14 |
+ 2024.04.02
대충 정리 하다면
DDR3 unbuffred + CBx + EVENT# = DDR3 ECC unbuffred (ECC 8bit 추가 + 온도 리포팅)
DDR3 ECC unbuffred + Err_Out + Par_in = DDR3 ECC buffred(or registerd) (명령과 주소 버스에 대한 패리티 추가)
----
심심해서(?)
서버의 DDR3-12800E 와 데스크 탑의 DDR3-12800U 메모리가
서로의 메인보드에 호환이 될지 테스트 해보는데
일단 현재까진
데스크탑에 DDR3-12800E ECC/unbuffered 는 문제 없이 인식(현재 2가지 메인보드 테스트)
서버에 DDR3-12800U 는 메모리 인식 오류로 bios에서 비프음 발생한다.
----
ECC/reg 메모리에서 error로 검색하면 아래와 같이 두개의 핀이 검색되어 나온다.
Symbol Type Description
CBx I/O Check bits: Used for system error detection and correction
Err_Out# Output (open drain) Parity error output: Parity error found on the command and address bus
비교해보면
39~40, 45~46, 158~159, 164~165번에 CB0~7
53번에 Err_Out
68번에 Par_in
187번에 EVENT# 핀이 차이가 난다.
Symbol Type Description
Par_In Input Parity input: Parity bit for Ax, RAS#, CAS#, and WE#.
EVENT# Output (open drain) Temperature event: The EVENT# pin is asserted by the temperature sensor when critical temperature thresholds have been exceeded.
근데 가장 왼쪽의 ECC는 데이터시트가 제대로 된게 맞나 의심이 된다. 아니면 ECC/reg와 ECC는 다른건가?
ECC 에서는 왜 Err_Out#이 없지? (혹시나 다른 제조사 껄 보는데 ECC U-DIMM 의 경우는 Err_Out이 없다)
아래는 ECC/reg 의 핀 아웃중 일부인데
Register and PLL 이라고 써있는 U6 칩에서 신호정렬후 다시 보내는 것을 확인할 수 있다.
------
DDR3L SR UDIMM - unbuffered
DDR3L ECC SR UDIMM - unbuffered ECC
DDR3L ECC U-DIMM - unbufferd ECC (Adata)
DDR3L VLP ECC DR RDIMM - ECC/registered
+
2024.04.02
Load Reduced 라서 LRDIMM 인데 핀만 봐서는 ECC/reg와 별반 차이가 없다
다만 Rank가 높다는게 위의 메모리들과의 차이이고, rank multipler 등의 별도 하드웨어가 추가 될 듯.
32GB (x72, ECC, QR) 240-Pin DDR3 LRDIMM
| uefi dxe pei (0) | 2024.04.01 |
|---|---|
| radix 4 - fp4 (0) | 2024.03.21 |
| 1.58bit (0) | 2024.03.16 |
| gps kalman (0) | 2024.03.13 |
| db 식별/비식별 관계 (0) | 2024.02.15 |
E5 v4 서버에서 부팅하다가 멈추길래
먼지 찾아보니 CPU DXE 이런 단계라는데 먼가해서 찾아보니
UEFI 에서 초기화 단계중 하나인듯.
| The Driver Execution Environment (DXE) phase is where most of the system initialization is performed. Pre-EFI Initialization (PEI), the phase prior to DXE, is responsible for initializing permanent memory in the platform so that the DXE phase can be loaded and executed. The state of the system at the end of the PEI phase is passed to the DXE phase through a list of position-independent data structures called Hand-Off Blocks (HOBs). HOBs are described in detail in Volume 3 . |
[링크 : https://uefi.org/specs/PI/1.8/V2_Overview.html]
| DXE = Driver Execution Environments. Once system RAM is initialized and the PEI phase completes, the DXE environment is entered. |
[링크 : https://rog-forum.asus.com/t5/x99/q-code-76-meaning/td-p/605026]
| DDR3 pinout과 ECC (0) | 2024.04.01 |
|---|---|
| radix 4 - fp4 (0) | 2024.03.21 |
| 1.58bit (0) | 2024.03.16 |
| gps kalman (0) | 2024.03.13 |
| db 식별/비식별 관계 (0) | 2024.02.15 |
설치
[링크 : https://gist.github.com/fxkraus/595ab82e07cd6f8e057d31bc0bc5e779]
alien 으로 rpm을 deb로 변환하던가
그냥 rpm을 풀어 버리면 안되나?
[링크 : https://www.lesstif.com/system-admin/rpm-20776290.html]
ubuntu 22.04 에서 압축풀어서 실행하니 되긴 한다.
| $ ./MegaCli64 ? MegaCLI SAS RAID Management Tool Ver 8.07.14 Dec 16, 2013 (c)Copyright 2013, LSI Corporation, All Rights Reserved. NOTE: The following options may be given at the end of any command below: [-Silent] [-AppLogFile filename] [-NoLog] [-page[N]] [-] is optional. N - Number of lines per page. MegaCli -v MegaCli -help|-h|? MegaCli -adpCount MegaCli -AdpSetProp {CacheFlushInterval -val} | { RebuildRate -val} | {PatrolReadRate -val} | {BgiRate -val} | {CCRate -val} | {ForceSGPIO -val} | {ReconRate -val} | {SpinupDriveCount -val} | {SpinupDelay -val} | {CoercionMode -val} | {ClusterEnable -val} | {PredFailPollInterval -val} | {BatWarnDsbl -val} | {EccBucketSize -val} | {EccBucketLeakRate -val} | {AbortCCOnError -val} | AlarmEnbl | AlarmDsbl | AlarmSilence | {SMARTCpyBkEnbl -val} | {SSDSMARTCpyBkEnbl -val} | NCQEnbl | NCQDsbl | {MaintainPdFailHistoryEnbl -val} | {RstrHotSpareOnInsert -val} | {DisableOCR -val} | {BootWithPinnedCache -val} | {enblPI -val} |{PreventPIImport -val} | AutoEnhancedImportEnbl | AutoEnhancedImportDsbl | {EnblSpinDownUnConfigDrvs -val}|{UseDiskActivityforLocate -val} -aN|-a0,1,2|-aALL | {ExposeEnclDevicesEnbl -val} | {SpinDownTime -val} | {SpinUpEncDrvCnt -val} | {SpinUpEncDelay -val} | {Perfmode -val} -aN|-a0,1,2|-aALL | {PerfMode -val �MaxFlushLines -val �NumIOsToOrder -val} -aN|-a0,1,2|-aALL MegaCli -AdpSetProp -AutoDetectBackPlaneDsbl -val -aN|-a0,1,2|-aALL val - 0=Enable Auto Detect of SGPIO and i2c SEP. 1=Disable Auto Detect of SGPIO. 2=Disable Auto Detect of i2c SEP. 3=Disable Auto Detect of SGPIO and i2c SEP. MegaCli -AdpSetProp -CopyBackDsbl -val -aN|-a0,1,2|-aALL val - 0=Enable Copyback. 1=Disable Copyback. MegaCli -AdpSetProp -EnableJBOD -val -aN|-a0,1,2|-aALL val - 0=Disable JBOD mode. 1=Enable JBOD mode. MegaCli -AdpSetProp -DsblCacheBypass -val -aN|-a0,1,2|-aALL val - 0=Enable Cache Bypass. 1=Disable Cache Bypass. MegaCli -AdpSetProp -LoadBalanceMode -val -aN|-a0,1,2|-aALL val - 0=Auto Load balance mode. 1=Disable Load balance mode. MegaCli -AdpSetProp -UseFDEOnlyEncrypt -val -aN|-a0,1,2|-aALL val - 0=FDE and controller encryption (if HW supports) is allowed. 1=Only support FDE encryption, disallow controller encryption. MegaCli -AdpSetProp -PrCorrectUncfgdAreas -val -aN|-a0,1,2|-aALL val - 0= Correcting Media error during PR is disabled. 1=Correcting Media error during PR is allowed. MegaCli -AdpSetProp -DsblSpinDownHSP -val -aN|-a0,1,2|-aALL val - 0= Spinning down the Hot Spare is enabled. 1=Spinning down the Hot Spare is disabled. MegaCli -AdpSetProp -DefaultLdPSPolicy -Automatic| -None | -Maximum| -MaximumWithoutCaching -aN|-a0,1,2|-aALL MegaCli -AdpSetProp -DisableLdPS -interval n1 -time n2 -aN|-a0,1,2|-aALL where n1 is the number of hours beginning at time n2 where n2 is the number of minutes from 12:00am MegaCli -AdpSetProp -ENABLEEGHSP -val -aN|-a0,1,2|-aALL val - 0= Disabled Emergency GHSP. 1= Enabled Emergency GHSP. MegaCli -AdpSetProp -ENABLEEUG -val -aN|-a0,1,2|-aALL val - 0= Disabled Emergency UG as Spare. 1= Enabled Emergency UG as Spare. MegaCli -AdpSetProp -ENABLEESMARTER -val -aN|-a0,1,2|-aALL val - 0= Disabled Emergency Spare as Smarter. 1= Enabled Emergency Spare as Smarter. MegaCli -AdpSetProp -DPMenable -val -aN|-a0,1,2|-aALL val - 0=Disable Drive Performance Monitoring . 1=Enable Drive Performance Monitoring. MegaCli -AdpSetProp -SupportSSDPatrolRead -val -aN|-a0,1,2|-aALL val - 0=Disable Patrol read for SSD drives . 1=Enable Patrol read for SSD drives. MegaCli -AdpGetProp CacheFlushInterval | RebuildRate | PatrolReadRate | ForceSGPIO | BgiRate | CCRate | ReconRate | SpinupDriveCount | SpinupDelay | CoercionMode | ClusterEnable | PredFailPollInterval | BatWarnDsbl | EccBucketSize | EccBucketLeakRate | EccBucketCount | AbortCCOnError | AlarmDsply | SMARTCpyBkEnbl | SSDSMARTCpyBkEnbl | NCQDsply | MaintainPdFailHistoryEnbl | RstrHotSpareOnInsert | EnblSpinDownUnConfigDrvs | DisableOCR | BootWithPinnedCache | enblPI |PreventPIImport | AutoEnhancedImportDsply | AutoDetectBackPlaneDsbl | CopyBackDsbl | LoadBalanceMode | UseFDEOnlyEncrypt | WBSupport | EnableJBOD | DsblCacheBypass | ExposeEnclDevicesEnbl | SpinDownTime | PrCorrectUncfgdAreas | UseDiskActivityforLocate | ENABLEEGHSP | ENABLEEUG | ENABLEESMARTER | Perfmode | PerfModeValues | -DPMenable -aN|-a0,1,2|-aALL | DefaultLdPSPolicy | DisableLdPsInterval | DisableLdPsTime | SpinUpEncDrvCnt | SpinUpEncDelay | PrCorrectUncfgdAreas | DsblSpinDownHSP | SupportSSDPatrolRead -aN|-a0,1,2|-aALL MegaCli -AdpAllInfo -aN|-a0,1,2|-aALL MegaCli -AdpGetTime -aN|-a0,1,2|-aALL MegaCli -AdpSetTime yyyymmdd hh:mm:ss -aN MegaCli -AdpSetVerify -f fileName -aN|-a0,1,2|-aALL MegaCli -AdpBIOS -Enbl |-Dsbl | -SOE | -BE | -HCOE | - HSM | EnblAutoSelectBootLd | DsblAutoSelectBootLd | -Dsply -aN|-a0,1,2|-aALL MegaCli -AdpBootDrive {-Set {-Lx | -physdrv[E0:S0]}} | {-Unset {-Lx | -physdrv[E0:S0]}} |-Get -aN|-a0,1,2|-aALL MegaCli -AdpAutoRbld -Enbl|-Dsbl|-Dsply -aN|-a0,1,2|-aALL MegaCli -AdpCacheFlush -aN|-a0,1,2|-aALL MegaCli -AdpPR -Dsbl|EnblAuto|EnblMan|Start|Suspend|Resume|Stop|Info|SSDPatrolReadEnbl |SSDPatrolReadDsbl |{SetDelay Val}|{-SetStartTime yyyymmdd hh}|{maxConcurrentPD Val} -aN|-a0,1,2|-aALL MegaCli -AdpCcSched -Dsbl|-Info|{-ModeConc | -ModeSeq [-ExcludeLD -LN|-L0,1,2] [-SetStartTime yyyymmdd hh ] [-SetDelay val ] } -aN|-a0,1,2|-aALL MegaCli -AdpCcSched -SetStartTime yyyymmdd hh -aN|-a0,1,2|-aALL MegaCli -AdpCcSched -SetDelay val -aN|-a0,1,2|-aALL MegaCli -FwTermLog -BBUoff|BBUoffTemp|BBUon|BBUGet|Dsply|Clear -aN|-a0,1,2|-aALL MegaCli -AdpAlILog -aN|-a0,1,2|-aALL MegaCli -AdpDiag [val] -aN|-a0,1,2|-aALL val - Time in second. MegaCli -AdpGetPciInfo -aN|-a0,1,2|-aALL MegaCli -AdpShutDown -aN|-a0,1,2|-aALL MegaCli -AdpDowngrade -aN|-a0,1,2|-aALL MegaCli -PDList -aN|-a0,1,2|-aALL MegaCli -PDGetNum -aN|-a0,1,2|-aALL MegaCli -pdInfo -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL MegaCli -PDOnline -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL MegaCli -PDOffline -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL MegaCli -PDMakeGood -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL MegaCli -PDMakeJBOD -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL MegaCli -PDHSP {-Set [-Dedicated [-ArrayN|-Array0,1,2...]] [-EnclAffinity] [-nonRevertible]} |-Rmv -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL MegaCli -PDRbld -Start|-Stop|-Suspend|-Resume|-ShowProg |-ProgDsply -PhysDrv [E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL MegaCli -PDClear -Start|-Stop|-ShowProg |-ProgDsply -PhysDrv [E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL MegaCli -PdLocate {[-start] | -stop} -physdrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL MegaCli -PdMarkMissing -physdrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL MegaCli -PdGetMissing -aN|-a0,1,2|-aALL MegaCli -PdReplaceMissing -physdrv[E0:S0] -arrayA, -rowB -aN MegaCli -PdPrpRmv [-UnDo] -physdrv[E0:S0] -aN|-a0,1,2|-aALL MegaCli -EncInfo -aN|-a0,1,2|-aALL MegaCli -EncStatus -aN|-a0,1,2|-aALL MegaCli -PhyInfo -phyM -aN|-a0,1,2|-aALL MegaCli -PhySetLinkSpeed -phyM -speed -aN|-a0,1,2|-aALL MegaCli -PdFwDownload [offline][ForceActivate] {[-SataBridge] -PhysDrv[0:1] }|{-EncdevId[devId1]} -f <filename> -aN|-a0,1,2|-aALL MegaCli -LDInfo -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL MegaCli -LDSetProp {-Name LdNamestring} | -RW|RO|Blocked|RemoveBlocked | WT|WB|ForcedWB [-Immediate] |RA|NORA | DsblPI | Cached|Direct | -EnDskCache|DisDskCache | CachedBadBBU|NoCachedBadBBU -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL MegaCli -LDSetPowerPolicy -Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL MegaCli -LDGetProp -Cache | -Access | -Name | -DskCache | -PSPolicy | Consistency -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL MegaCli -LDInit {-Start [-full]}|-Abort|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL MegaCli -LDCC {-Start [-force]}|-Abort|-Suspend|-Resume|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL MegaCli -LDBI -Enbl|-Dsbl|-getSetting|-Abort|-Suspend|-Resume|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL MegaCli -LDRecon {-Start -rX [{-Add | -Rmv} -Physdrv[E0:S0,...]]}|-ShowProg|-ProgDsply -Lx -aN MegaCli -LdPdInfo -aN|-a0,1,2|-aALL MegaCli -LDGetNum -aN|-a0,1,2|-aALL MegaCli -LDBBMClr -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL MegaCli -getLdExpansionInfo -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL MegaCli -LdExpansion -pN -dontExpandArray -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL MegaCli -GetBbtEntries -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL MegaCli -Cachecade -assign|-remove -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL MegaCli -CfgLdAdd -rX[E0:S0,E1:S1,...] [WT|WB] [NORA|RA] [Direct|Cached] [CachedBadBBU|NoCachedBadBBU] [-szXXX [-szYYY ...]] [-strpszM] [-Hsp[E0:S0,...]] [-AfterLdX] | [FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI] [-Force]-aN MegaCli -CfgCacheCadeAdd [-rX] -Physdrv[E0:S0,...] {-Name LdNamestring} [WT|WB|ForcedWB] [-assign -LX|L0,2,5..|LALL] -aN|-a0,1,2|-aALL MegaCli -CfgEachDskRaid0 [WT|WB] [NORA|RA] [Direct|Cached] [-enblPI] [CachedBadBBU|NoCachedBadBBU] [-strpszM]|[FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN|-a0,1,2|-aALL MegaCli -CfgClr [-Force] -aN|-a0,1,2|-aALL MegaCli -CfgDsply -aN|-a0,1,2|-aALL MegaCli -CfgCacheCadeDsply -aN|-a0,1,2|-aALL MegaCli -CfgLdDel -LX|-L0,2,5...|-LALL [-Force] -aN|-a0,1,2|-aALL MegaCli -CfgCacheCadeDel -LX|-L0,2,5...|-LALL -aN|-a0,1,2|-aALL MegaCli -CfgFreeSpaceinfo -aN|-a0,1,2|-aALL MegaCli -CfgSpanAdd -r10 -Array0[E0:S0,E1:S1] -Array1[E0:S0,E1:S1] [-ArrayX[E0:S0,E1:S1] ...] [WT|WB] [NORA|RA] [Direct|Cached] [CachedBadBBU|NoCachedBadBBU] [-szXXX[-szYYY ...]][-strpszM][-AfterLdX]| [FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI] [-Force] -aN MegaCli -CfgSpanAdd -r50 -Array0[E0:S0,E1:S1,E2:S2,...] -Array1[E0:S0,E1:S1,E2:S2,...] [-ArrayX[E0:S0,E1:S1,E2:S2,...] ...] [WT|WB] [NORA|RA] [Direct|Cached] [CachedBadBBU|NoCachedBadBBU][-szXXX[-szYYY ...]][-strpszM][-AfterLdX] [FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI] [-Force] -aN MegaCli -CfgSpanAdd -r60 -Array0[E0:S0,E1:S1,E2:S2,E3,S3...] -Array1[E0:S0,E1:S1,E2:S2,E3,S3...] [-ArrayX[E0:S0,E1:S1,E2:S2,E3,S3...] ...] [WT|WB] [NORA|RA] [Direct|Cached] [CachedBadBBU|NoCachedBadBBU][-szXXX[-szYYY ...]][-strpszM][-AfterLdX]| [FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI] [-Force] -aN MegaCli -CfgAllFreeDrv -rX [-SATAOnly] [-SpanCount XXX] [WT|WB] [NORA|RA] [Direct|Cached] [CachedBadBBU|NoCachedBadBBU] [-strpszM] [-HspCount XX [-HspType -Dedicated|-EnclAffinity|-nonRevertible]]| [FDE|CtrlBased] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] [-enblPI] -aN MegaCli -CfgSave -f filename -aN MegaCli -CfgRestore -f filename -aN MegaCli -CfgForeign -Scan | [-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL MegaCli -CfgForeign -Dsply [x] | [-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL MegaCli -CfgForeign -Preview [x] | [-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL MegaCli -CfgForeign -Import [x] | [-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL MegaCli -CfgForeign -Clear [x]|[-SecurityKey sssssssssss] -aN|-a0,1,2|-aALL x - index of foreign configurations. Optional. All by default. MegaCli -AdpEventLog -GetEventLogInfo -aN|-a0,1,2|-aALL MegaCli -AdpEventLog -GetEvents {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL MegaCli -AdpEventLog -GetSinceShutdown {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL MegaCli -AdpEventLog -GetSinceReboot {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL MegaCli -AdpEventLog -IncludeDeleted {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL MegaCli -AdpEventLog -GetLatest n {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL MegaCli -AdpEventLog -GetCCIncon -f <fileName> -LX|-L0,2,5...|-LALL -aN|-a0,1,2|-aALL MegaCli -AdpEventLog -Clear -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -GetBbuStatus -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -GetBbuCapacityInfo -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -GetBbuDesignInfo -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -GetBbuProperties -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -BbuLearn -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -BbuMfgSleep -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -BbuMfgSeal -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -getBbumodes -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -SetBbuProperties -f <fileName> -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -GetGGEEPData offset [Hexaddress] NumBytes n -aN|-a0,1,2|-aALL MegaCli -AdpBbuCmd -ScheduleLearn -Dsbl|-Info|[-STARTTIME DDD hh] -aN|-a0,1,2|-aALL MegaCli -AdpFacDefSet -aN MegaCli -AdpFwFlash -f filename [-ResetNow] [-NoSigChk] [-NoVerChk] [-FWTYPE n] -aN|-a0,1,2|-aALL MegaCli -AdpGetConnectorMode -ConnectorN|-Connector0,1|-ConnectorAll -aN|-a0,1,2|-aALL MegaCli -AdpSetConnectorMode -Internal|-External|-Auto -ConnectorN|-Connector0,1|-ConnectorAll -aN|-a0,1,2|-aALL MegaCli -PhyErrorCounters -aN|-a0,1,2|-aALL MegaCli -DirectPdMapping -Enbl|-Dsbl|-Dsply -aN|-a0,1,2|-aALL MegaCli -PDCpyBk -Start -PhysDrv[E0:S0,E1:S1] -aN|-a0,1,2|-aALL MegaCli -PDCpyBk -Stop|-Suspend|-Resume|-ShowProg|-ProgDsply -PhysDrv[E0:S0] -aN|-a0,1,2|-aALL MegaCli -PDInstantSecureErase -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL MegaCli -CfgSpanAdd -rX -array0[E0:S1,E1:S1.....] array1[E0:S1,E1:S1.....] -szxxx -enblPI -aN|-a0,1,2|-aALL MegaCli -LDMakeSecure -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL MegaCli -DestroySecurityKey | [-Force] -aN MegaCli -CreateSecurityKey -SecurityKey sssssssssss | [-Passphrase sssssssssss] |[-KeyID kkkkkkkkkkk] -aN MegaCli -CreateSecurityKey useEKMS -aN MegaCli -ChangeSecurityKey -OldSecurityKey sssssssssss | -SecurityKey sssssssssss| [-Passphrase sssssssssss] | [-KeyID kkkkkkkkkkk] -aN MegaCli -ChangeSecurityKey -SecurityKey sssssssssss| [-Passphrase sssssssssss] | [-KeyID kkkkkkkkkkk] -aN MegaCli -ChangeSecurityKey useEKMS -OldSecurityKey sssssssssss -aN MegaCli -ChangeSecurityKey -useEKMS -aN MegaCli -GetKeyID [-PhysDrv[E0:S0]] -aN MegaCli -SetKeyID -KeyID kkkkkkkkkkk -aN MegaCli -VerifySecurityKey -SecurityKey sssssssssss -aN MegaCli -GetPreservedCacheList -aN|-a0,1,2|-aALL MegaCli -DiscardPreservedCache -Lx|-L0,1,2|-Lall -force -aN|-a0,1,2|-aALL sssssssssss - It must be between eight and thirty-two characters and contain at least one number, one lowercase letter, one uppercase letter and one non-alphanumeric character. kkkkkkkkkkk - Must be less than 256 characters. MegaCli -ShowSummary [-f filename] -aN MegaCli -ELF -GetSafeId -aN|-a0,1,2|-aALL MegaCli -ELF -ControllerFeatures -aN|-a0,1,2|-aALL MegaCli -ELF -Applykey key <val> [Preview] -aN|-a0,1,2|-aALL MegaCli -ELF -TransferToVault -aN|-a0,1,2|-aALL MegaCli -ELF -DeactivateTrialKey -aN|-a0,1,2|-aALL MegaCli -ELF -ReHostInfo -aN|-a0,1,2|-aALL MegaCli -ELF -ReHostComplete -aN|-a0,1,2|-aALL MegaCli -LDViewMirror -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL MegaCli -LDJoinMirror -DataSrc <val> [-force] -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL MegaCli -SecureErase Start[ Simple| [Normal [ |ErasePattern ErasePatternA|ErasePattern ErasePatternA ErasePattern ErasePatternB]]| [Thorough [ |ErasePattern ErasePatternA|ErasePattern ErasePatternA ErasePattern ErasePatternB]]] | Stop | ShowProg | ProgDsply [-PhysDrv [E0:S0,E1:S1,...] | -Lx|-L0,1,2|-LALL] -aN|-a0,1,2|-aALL MegaCli -Version -Cli|-Ctrl|-Driver|-Pd -aN|-a0,1,2|-aALL MegaCli -Perfmon {-start -interval <val>} | {stop} | {-getresults -f <Filename>} -aN MegaCli -DpmStat -Dsply {lct | hist | ra | ext } [-physdrv[E0:S0]] -aN|-a0,1,2|-aALL MegaCli -DpmStat -Clear {lct | hist | ra | ext } -aN|-a0,1,2|-aALL Note: The directly connected drives can be specified as [:S] Wildcard '?' can be used to specify the enclosure ID for the drive in the only enclosure without direct connected device or the direct connected drives with no enclosure in the system. Note:[-aALL] option assumes that the parameters specified are valid for all the Adapters. Note:ProgDsply option is not supported in VMWARE-COSLESS. The following options may be given at the end of any command above: [-Silent] [-AppLogFile filename] [-NoLog] [-page[N]] [-] is optional. N - Number of lines per page. MegaCli XD -AddVd <devList> MegaCli XD -RemVd <devList> MegaCli XD -AddCdev <devList> | -force MegaCli XD -RemCdev <devList> MegaCli XD -VdList | -Configured | -Unconfigured MegaCli XD -CdevList | -Configured | -Unconfigured MegaCli XD -ConfigInfo MegaCli XD -PerfStats MegaCli XD -OnlineVd MegaCli XD -WarpDriveInfo -iN | -iALL MegaCli XD -FetchSafeId -iN | -iALL MegaCli XD -ApplyActivationKey <key> -iN Exit Code: 0x00 |
사용법
[링크 : https://www.broadcom.com/support/knowledgebase/1211161498596/megacli-cheat-sheet--live-examples]
5.4 Pre-boot MegaCLI
[링크 : https://www.supermicro.com/manuals/other/MegaRAID_SAS_Software_Rev_I_UG.pdf]
| SMC2108 SSD cachecade (0) | 2024.04.03 |
|---|---|
| raid 케이블이 잘못 연결됨 + LED 깜박이기 (0) | 2024.04.03 |
| MegaRAID Storage Manager(MSM) 설치완료 (0) | 2024.04.01 |
| msm (megaraid) 관리 설치 실패 (0) | 2023.11.14 |
| msm - Megaraid Storage Management (0) | 2022.11.27 |
아래 순서대로 설치
구버전이긴 해도 일단 돌아가니 ok
ubuntu 22.04 LTS 에서 24년도에 시도
| $ wget ftp://tsupport:tsupport@ftp0.broadcom.com/private/MSM/64bit-MSM_6.7_for_Ubuntu_Debian.tgz $ tar -xvf 64bit-MSM_6.7_for_Ubuntu_Debian.tgz $ sudo ./install_msm.sh $ sudo passwd root $ sudo passwd -u root $ cd /usr/local/MegaRAID\ Stroage\ Manager $ ./startupui.sh |
대충 하라는대로 하면 끝. 왜 저번에는 시스템이 날아갔지 -ㅁ-?
아래 단계에서 ubuntu 기본 계정은 root가 아니라서 view only로 해야한다.
요건 view only로 로그인 시 화면, Actions 쪽에 전부 검은색 출력되어 클릭이 되지 않는다.
root 계정 추가해서 Full Access로 로그인시에는 전체 권한이 되는데 이 경우에는 Actions 쪽이 활성화 된다.
create virtual drive 클릭!
simple
advanced
| raid 케이블이 잘못 연결됨 + LED 깜박이기 (0) | 2024.04.03 |
|---|---|
| MegaCLI (0) | 2024.04.01 |
| msm (megaraid) 관리 설치 실패 (0) | 2023.11.14 |
| msm - Megaraid Storage Management (0) | 2022.11.27 |
| smartctl을 이용하여 개별하드 상태보기 (0) | 2019.03.15 |
예전 글을 따라가니 어느정도는 되는줄 알았는데 영 막혀서 삽질..
ubuntu 22.04 LTS
1. openjdk-8-jre 설치
| $ sudo apt-get install openjdk-8-jre |
2. icedtea 설치. 단 openjdk-11-jre가 같이 설치된다.
| $ sudo apt-get install icedtea* |
3. openjdk-8 설정(보안)
jdk.jar 관련 암호 알고리즘을 꺼준다. 꺼주지 않으면 조금은 엉뚱한 "cannot grant permission to unsigned jar" 에러가 뜬다.
| $ sudo vi /etc/java-8-openjdk/security/java.security 672 # jdk.jar.disabledAlgorithms=... |
[링크 : https://techblog.jeppson.org/2018/01/fix-icedtea-cannot-grant-permissions-unsigned-jars-error/]
4. icedtea 설정 - JVM 셋팅에서 openjdk-8을 쓰도록 설정한다.
$ itweb-settings |
5. javaws로 실행
$ javaws launch.jnlp |
2020.09.17 - [하드웨어/Server Case & board] - jnlp on ubuntu/chrome
[링크 : https://techblog.jeppson.org/2018/01/fix-icedtea-cannot-grant-permissions-unsigned-jars-error/]
ipmi 로그인 기본 계정은 ADMIN / ADMIN
| 보드에 ECC/reg 장착하기 (0) | 2024.04.09 |
|---|---|
| 구형 시스템 메모리 클럭 제한 (0) | 2024.04.05 |
| xeon에 non-ecc가 가능한가? (0) | 2024.03.31 |
| iKVM 접속 오류 (0) | 2022.11.27 |
| supermicro X9SCM-F IPMI LAN(dedicate) (0) | 2022.02.18 |
와씨.. 2만원으로 올랐네
그나저나 협찬이 왤케 초라해졌냐.. 그래서 비싸졌나?!
| 오랫만에 약간 먼 자전거 (0) | 2024.04.06 |
|---|---|
| 간만에 자전거 (0) | 2024.02.17 |
| 라이트 손..상? (0) | 2023.05.21 |
| 이런.. 자전거대행진 신청 실패 (0) | 2021.11.09 |
| 라이트 청소 (0) | 2021.10.26 |
|
